Loafer61's latest activity

They seem to use hyperspark as their ignition. Love the look of the sniper 2 as a fuel injection replacement. https://www.holley.com/products/ignition/hyperspark_ignition_for_sniper_efi/

I’ve done a bit of research on this of recent. I was going to go megasquirt but am now leaning towards either Holley sniper 2 or fitech for my build. I don’t want to be messing about with maps etc. I just want something that self learns and had...

Interesting…

Discussion here on a Series 3: https://www.landyzone.co.uk/land-rover/electronic-ignition-123-vs-britpart.355918/#post-4945249 And a good (old) discussion here: https://forum.britishv8.org/read.php?6,30614,page=1 However after messing about...

I went the whole hog and bought a Momo for my Disco. More room is essential, I think that looks fine!

Here is a picture of the wheel, a Bolt on bits special from eBay. Used them for a few bits and pieces. More elbow room.

Front ATB is in! Of course its the Ultrabuild spec from Xcess4x4. Same ATB thatbwas in the D2, just stripped, cleaned and rebuilt. Also resealed the cam cover cap, alternator Vac line. Both had little leaks so hopefully im leak free now...

Folks, I'm so happy. Today I spent a few minutes at my Landy, because I wanted to be able to move on refitting the fuel pump the next days. My solution: I created my own "Adapter-Ring-Fitting-Tool" using two steel-angles and a few bolts: That...

Hello Ladies & Gents, I post this here, because I think it might be an "general" Topic, regarding all Land Rover Models. If this is the wrong sub-forum please move it to where it belongs. The story of this "repair" started a few month ago...

I wanted to check the oil pressure to rule out a low pressure problem while investigating a tapping noise, unfortunately the method to connect a gauge as described in the workshop manual is impossible on the Thor engine due to ancilliaries and...

I can see you have the turbo now, I was just going to say that Andrew at Allisport is a mine of information (fairly obvious) and a dang nice & helpful bloke. You won’t go wrong with anything with their brand on (or associated with). It looks...

Will it ever warm up???? I suppose the last 2 days haven't been too bad, my blood must be getting thin. I have a short list of things to do and a couple of days would do it. I've got a front anti-roll bar to fit and a straight through silencer in...

As I keep picking away at silly little things, which need doing, the latest of which was a new battery, as the one fitted was very small and after a 20 mile drive on the Dual carriageway with the sidelights on, I left it outside the Engineering...

Erm, so where was I ...... OK I was Adjusting the wastegate to give a little more squeeze, and was edging up a bit at a time when at 14 psi it started to get noisy, you guessed it, we have found the limit of the original inter-cooler core, which...

Testing... To be Continued.........

Scabby wheels: I'm a shallow guy who likes shiny things I suppose These were contributing to the Stop this and throw the book at it Look . It's a pain to rub them down, but the weather isn't great and Neither is the Telly,so after an hour or...

It is more or less ready to use now, I have went through most of it and have sorted what needed sorting and will use and evaluate what happens next. Rear axle: oil changed, new calipers and pads. Will change out backplates for the MOT as they...

Been Busy doing battle with the Landy the last couple of days. It would appear that some work was done at chassis exchange time, but very little thereafter, so lots of siezed /mullered bolts, but slowly getting there. All lubricants renewed...

The Main battle commences tomorrow with a visit to the steam cleaner. I have been over it with my cold machine and got about 80% of the crud off, so should only take an hour or so to go over it, then it starts in earnest. I'll be down at my old...

The 2nd battle for the brakes The fronts were not really much better than the rears, but the N/S Freed off and got put back together The O/S was a different story the outer freed off, but the inner refuses to move, so I've put in a slightly...

Bear with me. I'm transferring content here, so that when I start to ask questions, you will better know what has and hasn't happened.

The War of the Land Rover. Pt. 1 The battle for the brakes It is Mot'd until the end of Sept, so I have a bit of time to sort it out. Since getting it I have roughed out a plan of attack. 1. Do something about the Driving position. Defenders are...

Well enjoy working on your pride and joy…found the same working on my old pal… a lot of the parts I found were not quite to the same standard as the old stuff…bit of a mine field finding parts. Shop carefully boss. 👍

Spending a few bob on my Landy making things look nicer and getting a few nice goody’s because haven’t in a while Always wanted one of these tow balls and stumped out over £40 quid and this is how it turns up, its quite scrappy do da day but of...

I think that is what Tonks meant?

Don't forget the D1 transfer box is rod operated unlike the D2, worth a check if that still correct.

Yes, indeed! Turn that picture 90 degrees anticlockwise and the fan would be below them.

New HT leads and new fuel filter fitted. Just waiting for the new distributor cap and rotor to arrive. I changed the plugs (lordy!) for new and all the screw on caps were loose, they are not now. It is firing better but not perfect yet. The...

And that steel plate won’t be too much of a drama!

Thanks Tonks! I have a complete D2 setup…