Definitly need more information regarding what tyres for a towbar height and what trailer you are trying to tow that needs such a low hitch. And maybe a picture of your current setup. After that will be better placed to give advice. My towbar is...
In poor condition, Defender seats are rubbish. The foam falls to bits over the decades, making them lumpy and uncomfortable. The solution is to simply refurbish them, rather than mess around trying to fit other seats in there. New internal foams...
Think man! Without one how else do you run all the cables up to the roof lights you don’t need!
I got my original mushroom top one galvanised and am planning on doing the same with the one for the station wagon. I just need a new tube as the one...
The flying lead off the back is the positive, and would have been connected to the solenoid which is essentially a giant switch between that cable and the cable to the battery. The motor earths through the casing onto the block. You could put an...
The top bottom bracket can be fitted using the existing mounts. It is only the reel
Itself that you need to find a way of mounting. On my hardtop I mounted this to some 10mm angle iron that was bolted to the original position on the rear bulkhead...
That one. The ring terminal going into the starter itself will spin the engine over if you put a jump Lead onto from the battery. I would favour bump starting if it was not a 19j. My 200tdi takes so little to start that I can get it loving...
Storage at all is not cheap. that is how I have justified leasing the field I now have, the cost to store the two things in it elsewhere means that after three months the field has paid for itself and the other 9 months I have a free storage and...
@Hicap phill will probably be able to help. However bear in mind that any hicap that has has been used is likely to have a fairly battered rear tub (no judgment of @HiCapphills land rover intended!)
I agree with the above and to be honest even if you buy a new one rather than rebuilding your current ones (which I am currently doing) I would still fit stainless piston before fitting. If they are new you dont need to do anything else just...
Or you will find out what it is worth and not sell it. I like watching the vehicles trying to be sold that get put up as a classified a couple of times and dont sell, then an auction that doesn't sell and reaches half the classified price a...
yep, that is the same with the major, original book spec is S.A.E. 30 H.D in engine, gearbox, and rear end (also the hydraulics on a major). Although there is a school of thought to use modern multi grade oils as you can still get HD30 I run that.
I don’t like keeping count. It makes keeping the vehicle even less justifiable than it already is! I have all the paperwork and could add incoming wanted to. But I feel the actual Figure would make me sick!
Cannot agree more with the above! I bought the boomslang kit and was very unimpressed. I then Set about modifying it to run direct from the battery and for the relays to be in a sensible position and then gave up and stripped it for parts. With...
That was my first through as well. If that is the case you can build up the switch contacts with solder so they make contact again as a temporary fix while you wait for the new part to arrive.
It is not as simple as fully comp insurance any more as lots of them have removed the third party cover on other vehicles. Wife doesn't have it on hers, and out of the three fully comp policies I have only the vintage tractor has the third party...
So convert it into what is a more practical vehicle for you! I am in the process of rebuilding a station wagon body to put on my 110 hardtop now I have a family as side facing seats in the rear tub do not mix well with baby car seats! Depending...
pics would definitely help, and it also depends on the design of your brackets. I had to change form the angel iron brackets to flat bar ones when I fitted my tank guard but to do that I just combined the later style tow bar that used these as...
I do not believe even with your experiment for observations of having a slack alternator belt. Normal running no issue, alternator spins freely with no belt slipping. turn on all additional lighting (at the time 10x 100watt halogens) and the belt...
Well first coat of high temperature caliper primer is on. Think it will Probabaly need a second coat before a top coat but I will keep this updated with how it turns out. Went for gun metal grey in the end as a colour because everything else I...
I am well aware that you never get back the cost of rebuild. But as I said I monitor the prices and have search alerts setup for these. Like this one basically the same for 17k LINK. or the original ad for the one listed at 18k LINK
or some that...
A tdi engine with a galv chassis and galv bulkhead I think that is a cheap price regardless of body configuration. If it was a station wagon I would have expected it to be nearer 20k. But this is why i am asking if it is just realistically priced...
a prop uj failure would not cause this, if it only happens under breaking that suggest something is amiss with the brake system, possible a warped disc, but again not the usual symptom
As above rotational play is normal and to be expected with...
EBAY LINK
Not my ad and the vehicle is nothing to do with me, but I have a search saved for galvanised 110 to monitor prices for insurance value purposes on mine. This seems a lot cheaper than they are usually advertised for considering the...