Bobs110's latest activity

Oh and I’ve found the ideal spray booth ! Forget building it in the garage! I’ve just been granted planning permission for an extension on the back of the house replacing my conservatory which we seldom used for a 8x6mt kitchen / family room, so...

Steady progress this weekend have got the gearbox tunnel cover and the steel bit that joins it to the bulkhead ready for primer after some patch repairs. Handbrake and gear sick cleaned and painted, window hindges cleaned up and ready for some...

Yes price is per kg, not sure how much that is at the moment. Previously Ive sent them to Roften in Merseyside but this time they are heading to Shropshire galv.

I’ve had two bulkheads galvanized so far and had no issues, if they do decide to drill a hole I can always fill it in with lead solder before painting, I’ve used this method on galvanized front bumpers to fill in the end cap holes. Beauty with...

As the weather is so bloody awful today think I’ll hide in the garage, plan is to patch up the bulkhead to tunnel cover (sand blasted revealed a few holes) then straight out the tunnel panel, clean up the heater box and fan and get everything...

All the steel work including the bulkhead and inner wings are back from the blasters, a few drain holes added to the roll bar hoop and they are ready to go to the galvanisers next Wednesday. Notice that I’ve attached some unistrut as a brace...

Its done !!! And Im also done in ! 12 hrs in the man cave, 1lt of etch primer, 2 lts of high build primer, 3 sheets or 80 120 and 400 grit block sanding pads and two bottles of Proper Job IPA and the tub is finally ready for top coat.

Thing is with LR is to me they are a work horse. Spent ages on 1 build & jumped into the nice leather trim… & scratched them with a Jean button.. trim out & back to cloth. The Hicap was a purpose built motor. All straight, gleaming paint...

Cant wait to get this rear tub in primer it’s starting to grind! I would say to anyone restoring a landy that it’s the most time consuming piece of the jigsaw to get right and the most visible once done, get it wrong and it will annoy you every...

Righ hand side of tub skimmed with fine filler and block sanded to smooth out any small dents

Another day of sanding, priming, sanding, priming, sanding, gravitexing, priming and now finally beer time …. Mrs Hughes is becoming more and more suspicious as I’m spending every minute in the garage and complaining that my back and wrist hurts…...

Windscreen surround, bonnet, roof bar and bonnet catch slam panel all cleaned up, etch primed and primed. Appart for a few runs which will flatten out with some sanding their looking good 👍 will flip the bonnet over tomorrow and prime along with...

Fitted the bulkhead reduction kit this evening, will certainly help getting my lanky frame in between the seat and steering wheel ! With room to spare …

Bit the bullet and decided to strip it right back to bear ali, came across a few deep dents that had been filled in which is not what I would want to be re painting over. Let the metal bashing begin. Have to admit I do hope mrs hughes doesnt look...

Tub underside all finished, etch primed and then undersealed with gravitex stone guard, ready for primer and paint. Will start on the outside next flattern then fill and block sand.

Ah.. I hadn’t noticed that, to be honest I wouldn’t fancy turning this over by hand you’d certainly break a wrist trying

New 1.6mm ali inner wing liners cut to shape and ready to be panel bonded and rivited over the original wings to give a smooth as new finish to the inside of the tub, also bonded 2mm sheet to the original floor here it is with some weight on it...

Rear wheel arches strengthened with formed inner ali sections panel bonded into place, few other repair sections fitted. New inner wheel arches bonded and rivited along with new floor and rear cross section all bonded rivited and bolted using 5mm...

And in between all of the landy stuff I managed to give the bike a service before the trip

Rear tub dismantled, steam cleaned and sound proofing heat gunned off. Measured up for new 2mm ali floor and inner wings.

Seat box all complete ready for etch and primer, bonnet all cleaned up with the steel work rust converted and new seam sealant just to add some strength and dampening to the ali skin. Have a few small dent that needs skimming and sanding then its...

Tonight’s mission is to prep the seat box for primer, two new end sections and some metal bashing and its nearly ready for paint. Just have to wait for the panel bond seam seal to go off. Top tip to remove sound proofing, heat it up with a heat...

All the axle and suspension parts are now painted, dry and stored. All of the rusty bits have been dropped off at the blasters, in the meantime it’s bodywork fetteling oh how I have missed weeks of straightening panels and endless DAing 😔 on the...

slight delay with progress this week due to a stinking cold … but Im back on track . Chassis is now finished and parked up outside out of the way. Hub assemblies all cleaned up rust converted and trailing arms etc free of very stubborn bushes...

It’s started again .. my neighbor’s must think that the misses is having an affair with Simon the DPD delivery driver 😂 as hes starting to spend more time in the house than I do

Chassis now complete after 3 coats of paint ! I will guarantee it for another 40 yrs. Front axle new diff pan welded on, rust converted and painted. Its a shame that the paint dulls off when dry as I do like the gloss finish but then again it...

Where better to be on a wet and very windy day …. No dont be stupid not in the house watching the telly or baking a cake, in the man cave disassembling and degreasing the front swivels and hubs of course. With afternoon “panad” over (thats Welsh...

Well what a productive day, I feel better now that I’ve started to get stuff painted, its either that of the fumes off the thinners. Cleaned the rear calipers and painted them red, cleaned rust converted and painted the rear hubs and drive...

This early bird has caught no worms yet but has so far rust converted the rear axle, acid etched the chassis with T wash, de greased and hot washed and hung it out to dry… no literally hung it out to dry … look at the photo below ! dont want any...

How much would you be looking for it ? No hang on …. I’m sticking with the 2.5 n/a …… on second thoughts the last 300tdi was great ….. no Mark stick to original….. just think how much more economical it would be and more environmentally...