Get someone who has the GAP tool (just maybe if unlicensed to your VIN ) it will help.
I have just gone through a similar experience with the level sensors on my L320 and with WITHOUT using MY Gap tool Igot into quite a mess as forgot to disable...
I considered swapping sides but I was risking destroying the nearside rear as the one I have just replaced did not want to undo and screws had to be cut.
So I carried out guidance height on GAP and simply level offside while sitting in the...
Hmm , might try that , but would only be a visible difference as unless of course I look at live values on GAP iid . I seem to remember that when I originally fitted this sensor it sent back a different value than the rest of originals. So I will...
I am beginning to wonder whether the Brittpart is incompatible with the other sensors assuming the rest are genuine L/R. I had this problem on an L322 AND Aftermarket ABS sensors bought from Rimmers no less, as soon as I replaced them with L/R...
So the light is still off on dash and Mot , passed . Height onthe rear offside still low after guidance set up and E0 shows up on guidance. Incefently the original fault code still comes up C1A00-54 . I have since re-enabled after this an re...
To be honest, sometimes the bracket needs 'realigning' - send it down to access, up to offroad then back to normal between each 'tweak' - they can twist by a few millimetres when you remove the bolts if there's any corrosion, it looks OK but...
Quietly confident that Dynamic Roll is fine now , but new rear left height sensor too low . I have used the guided cal twice but it errors out . This is because the module was not active in the ecu info . Once activated . It cleared the dash...
To add , you need to assess where the leak is coming from, most likely pipes from the valve block to to pump and anti roll bar . Even the couplings on to the roll bar actuator .
You can expect the pump to fail, possibly seize, and rip your aux drive belt to shreds, which if you then keep driving will cause an overheat and no alternator output.
It's usually corroded pipework, not the ARB but it does require proper...
An update
I have had several helpful instructions from the GAP team.
To cut out everything from Module Calibration to CCF files which the AR Control module seemed to be inactive , so made active and the red Roll light disappeared and fault...
I have had the Company’s diagnostic reply and it’s a little confusing as they think I haven’t sorted out what my problem is .
C1A0054 Dynamic response control module
New control module
Configure the new module using the approved...
I suppose if you consider a large diagnostic that has to do 100 more vehicles of different types then I would say fair enough , this is good but for a few Land Rovers specifically then the interface can be smaller.
Anyway , I have communicated...
No not contacted yet .So I have included a couple of photos I have extracted out of the GAP manual . Maybe try again on calibration , guided maybe , but have done this and got the error E16 . GAP CONTACT NEEDED!
Yes that is the part I replaced...
Yes I have done , avoid that is . I Flashed the engine ecu before when I requested the standard mapping from GAP , as when I bought it the owner had it mapped for power and economy and it kept giving a fuel regulation problem . Anyway I digress ...
I get the facility to re-enable EAS as you say I may be missing something. I'll have another look , there is a facility that I can flash an ecu , suffice to say I have avoided it so far , might be brave later!
"thinks" that you replaced the...
I saw a guy on you tube resolving the code I get , Sorry the pic I put on is not very clear its Code C1A00-54 and he puts the fault down after calibrating height after sensor replacement then it muddles the Suspension module , he suggests putting...
Doing guided calibration on four corners will complete , an error E16 appears on GAP . Got to Active Roll cal and e red error appears on the dash and this faultS I will try battery reset , there seems to be a confusion between modules
Yep done that
What’s the best way of resetting the ecu that controls the height on RR. Now that the new height sensor has been fitted and the suspension over 4 days had dropped to one side it doesn’t want to play. Switching up or down the car goes to opposite...
New sensor fitted , no warning lights as in Suspension and dynamic roll , all faults cleared , but vehicle still leans to the right as after 3 or 4 days waiting for the level sensor the air supply had given up. After installing the sensor the...
No not necessarily, only verified that the new sensor I had by chance is showing a varying voltage when moving the small arm attached, but at least it proves that the modules might be a bit happier. I will see if whole the new borrowed sensor...
No in general the roads are salted here a lot because of our weather .up here, before my ownership who knows , I have owned since 2021.Anyway the plug is off just now and Ill clean with elect contact and put back on with some Vaseline around plug...
No its not the same , , a whole heap a module mis matches then when cleared the one that remains is under suspension , the rear right height indicator . Still the same Dynamic roll light which go out on occasion
All back together now but will...
Hey HO it didnt last ! One week and now the modules connected to give messages to Active roll , decide to give out a bad connection from the rear height sensor and threw out the the roll light to amber again.