Latest activity

As long as the collars on each pipe sit against the black plastic they are are home. The aluminum collar should be sat equally across the pipes in relation to the black plastic receiver 👍

Been feeling rough for nearly 2 weeks with a cough was bringing up green blobs, thats clearing up still got a cough every now n then. Was blowing my hooter & my ear was blocked mading some weird squeaking noise been feeling dizzy for 2 days like...

Got the bulkhead painted in a fashion, first time spray painting its not to bad but it will do me. will get it fitted then see if I can get ideas of where I have to run things, had 2 bolts lined up what I thought were for bulkhead but to wide...

i pulled them all when i was refitting the engine. they didnt look too bad but i will pull them again

i pulled the engine and con rod ends look a little worn; but thats fine. nothing insanely crazy. didnt pull mains yet, but i feel like that doesnt have priority rn.

I'm in France, but also have the 2.4L Puma. I service my own vehicle and for the engine oil I use FEBI BILSTEIN - 5W30 Longlife HC-FO Link if you are interested. I also used Mann air-filter with a genuine LR fuel filter.

Oh Aye ye ole Arnold Schwarzenegger bog roll, hard as hell & takes no poo 🤣

Or back off adjuster fully check pushrod in cup and slider not broke

Hi all ,so my sump plug won't budge no matter what I try whacking a smaller socket on ,heat ,wd40 overnight ,it's stuck but I have just been told the black tube that's lower than the sump plug can be pulled instead to empty the sump is this...

Thanks. I've since found that thread but sadly no nothing of use there. Looking like there's nowt about like Siera said

I wondered if anyone has any thoughts on how many injectors I should change, based on the readouts and the leak off test? I’m thinking definitely 4 and potentially 1 too… trying to refrain from throwing too much money at parts given its overall...

No swimmin down ere for me. Lots of peeps dint get the memo and are swimmin in Stokes Bay, is only round the corner, dummies.. Lee-on-the-Solent sea pollution warning after sewage pipe burst - BBC News -...

Not a military no, it's a bit of a bitsa to be honest, cobbled togerther (badly) by The Butchers of Hereford 4X4. The offside wing is a TD5 with the square hole for the side repeaters and the nearside is a 200tdi wing, I think, which has the...

Hope the breakfast was nice 😯😯 Izal was the name of the paper

Nor me ... not sure it's worth £480 spons though ....

It’s onna stick, Tusk!

"Bend over and take it" means to not respond and just accept being insulted. I did not do that. I was insulted and patronized and for a little while I tolerated it but after about the 10th time I had enough. I eventually decided not to bend...

........... knew such a thing existed. https://www.ebay.co.uk/itm/376237746628

Quick update: Managed to screw it down, but I'm not convinced it's right: See those two little teeth on the edge of the bracket? Top one doesn't seem to be making contact with the matrix, and the bottom one is on top of the inlet instead of...

Tango in the night

Cam follower? The big roller, or the slider? A bore camera down the push rod hole might be helpful.

My son's Ninety are the same as those above, stuck on . Stupid thing, I'm going to wrap some tape round it and wedge it in the hole.

Back again. Greased up the O rings but still no luck with the securing bracket. Does the bracket slot in to place first before tightening? Right now it's loose and I'm having to push it up with my hands when trying to screw it on. I've pushed...

https://www.ebay.co.uk/itm/365702278077 ^^^ beat me to it

Thread 'Rear wheel arch repair panel' https://www.landyzone.co.uk/land-rover/rear-wheel-arch-repair-panel.376874/ Anything here?

@miktdish is your motor ex military? Only wondering as my 85 had these and then changed on the TDIs And you get a better pack of these…