Latest activity

Don’t suppose you remember what ohms resistor you used do you?

I take it out from above… loosen, let it drip, then lift out.

W got feed up washing my T shirts now it's mandatory that I wear a bib or no bacon and runny egg with hP sauce 😊😊

I've seen this mysterious starting behaviour before. The Landy concerned had two bad segments on the the starter's commutator. This means a lottery when going for a fresh start, as it depends on where the motor stopped rotating the last time it...

Gearbox to engine nuts are 9/16". The top two are either 9/16" or 5/8".

The hole is there, but it's clogged. I think the radiator isn't original and the previous owner replaced it. And I think he made a mistake. So I'm wondering how the oil cooler water circulates if this hole is clogged.

I use one of these. Decent lenght probe makes it easy to reach awkward bits. Neilsen CT0998 3pc Mechanics Stethoscope

You underestimate my ability to burn things..

If by blocked you mean the hole doesn't exist on that port, then it's fine and you can leave it. The updated radiator design is supposed to be like that.

In Newcastle it's a stottie cake. Best eaten with ham n peace pudding.

Like police scotland

Wix scotland

Now fair enough you might set the car on fire with a plumber torch soldering tiny wires but you can get electric soldering irons now which would be a little safer or even small gas powered ones lol.

Tis a bacon batch.

Ooh, the next thing is listen to the engine running with what resembles a doctors stethoscope. The noise could then be almost pin pointed to an area and give you an idea of where to go next. I had a client bring a jag with the 2.7td v6 to the...

Might grab some trusty Wagos out of the van then make a better fixing. Don’t trust myself not to set the car aflame with a soldering iron.

Had same on my Had same on my P38 SRS light kept coming on because of the connection so in the end I cut it out and soldered the wires together, end of problem.

Hello Sierrafery, I'm asking about a problem with my Discovery TD5. I have a 1999 10p engine. I've removed and cleaned my radiator. I noticed the hole coming from the oil cooler is blocked. Can I leave this setup on this model or do I need to...

@dag019 Tagged him for you @Phippu

Right so quick update - drove back from a cycle to the unit to dump the bike etc and had a quick nose under the seat to check which connector. Moved it slightly and now the SRS light is gone with no message either - so thankfully not the clock...

Before trainers were invented, it was a gym shoe, for those who remember them. 🤣 But that was in Avon or Zummerset, or Glowwwcestershire!!

Put the boards on top. Less stress on the metal work. If you done the angle iron method bet you would catch your legs on them unless you remove these after use.

😨 15 year old battery is going some!, when you checked the earth straps does that mean you removed them wire brushed terminals clean including where they mount on chassis / engine and you have done same with positive connections , battery...

It’s a dap for a trainer in Wiltshire

Donno. Got a parts manual? Google the part number and you'll get the thread and dimensions.

Hmmm. How would you tell if the chassis was still OK? Not that you'd be bothered on selling it, if you are a dyed-in-the-wool scrote. This has got me thinking. If the running gear is still OK, i.e. bushes etc, tyres, shocks it MAY be an...

Cheers guys! Really appreciate all the help. Will have a look round.

Hi all quick question, What are the sizes of the following: Nuts to mount the gearbox to the engine? The two top bolts which mount the flywheel housing to the engine? Running a late 2a petrol. thanks in advance!

So hot at the moment got some weeding done

Cheers buddy, yeh i've seen them. But not had any luck finding the one thats got both male and female connections. Only seen either single female or double female. Could i simply replace this connector with a double female and replace the single...