- Posts
- 31,399
- Location
- North Shropshire
is it like star trekking, but fluffier?
P38A Air suspension not rising in one corner
- Thread starter Montyjohn
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Datatek
Well-Known Member
- Posts
- 43,947
- Location
- Near Poitiers SW France
Nah, it's like mule trekking where you use the animal to carry your luggage
- Posts
- 31,399
- Location
- North Shropshire
Don't know if it's related, but my eas had never worked as it's supposed to, eg opening a door doesn't halt the system etc.
I once tried to operate via nanocom with the engine off, it would raise on the right but not the left, or even 3 corners.
Never got a fault, but as soon as i started the engine it would level out to the selected height
I once tried to operate via nanocom with the engine off, it would raise on the right but not the left, or even 3 corners.
Never got a fault, but as soon as i started the engine it would level out to the selected height
- Posts
- 4,458
- Location
- Rotherham
£45 off the bay of e fully refurbished with windows 8
Datatek
Well-Known Member
- Posts
- 43,947
- Location
- Near Poitiers SW France
- Posts
- 12,139
- Location
- Sud ouest France !
You could try Swapping the two sensors on the front axle to see if the problem shifts to the other side
You can use the nano ( eas/ inputs) to see if the ecu is receiving the door open status, and you can check becm to see if the doors are sensed as open/ closed.
- Posts
- 31,399
- Location
- North Shropshire
yep, it showed all as it should
- Posts
- 4,458
- Location
- Rotherham
I know but all I have it for is to run the EAS software and keep a copy of Rave on , nowt else.Win 8
Datatek
Well-Known Member
- Posts
- 43,947
- Location
- Near Poitiers SW France
You have done well to get the EAS software to run on 8 if you are using a serial to USB adaptor
- Posts
- 4,458
- Location
- Rotherham
Already had the drivers. Just installed and it ran fine. Took your advice and installed them first before plugging in the adapterYou have done well to get the EAS software to run on 8 if you are using a serial to USB adaptor
I just got a HP ElitePad PRO G2-1000 running Windows 12 for £74.99. It runs EAS Unlock perfectly. It came with an OTG USB adapter & works with the cable that Storey sent me when I bought the V4 licence. It didn't work with a couple of other cables that I have that were purchased on eBay as there was a comms error.
https://www.ebay.co.uk/itm/325644071523
https://www.ebay.co.uk/itm/325644071523
Datatek
Well-Known Member
- Posts
- 43,947
- Location
- Near Poitiers SW France
Think there is a typo there, it's Win11 not 12
Indeed you are correct.Think there is a typo there, it's Win11 not 12
As a tablet I don't find it as nice to use as an iPad but I think that's partly because its touch screen seems less precise but also the need for a double click rather than a single click to launch applications.
- Posts
- 18,963
- Location
- Buckinghamshire, UK. ('95 DT)
I suspect you can change that in settings somewhere. Input devices or somilar, maybe.
Datatek
Well-Known Member
- Posts
- 43,947
- Location
- Near Poitiers SW France
If you enable the task bar and put the app icon in there, it's a single click to open.
Thanks I will give that a go. I still can't quite believe how ridiculously cheap these tablets are.
