Recent content by gulfbluersr

Hi Ben, just looked at your eBay site, working an a site the rest of the week with little phone service, can you pm me a price on a pair of diffs, one 2 pin one 4 pin, also on a pair of complete axles, air springs not needed as have new already, again 1 x 2 pin and 1 x 4 pin so 4.6 p38...

Thanks Wammers, I'm into taking a bit a gamble, easier now I know they are all the same ratio, I though they were just wanted to make sure. Some places are happy to offer 90day warranty and sell as tested.....yeah right I'm sur they will all stand by that!! But will do some homework on...

Hi, now that I have sorted my EAS problems I want to move onto the next problem!! The diff or diffs in my 1999 4.6 are very noisy, they have been since I bought the car, I've left them until I have sorted other problems but think I better get them sorted! I checked the oil in them, the...

Just to update this thread a bit, I found and won on Ebay a nice cheap working valve block, decided that it was worth a try just to put my mind at rest as for the block that I had resealed in case I had given myself any new problems...... 1st I put the ebay block in and car went up, but then...

Thanks Wammers I'll try again tomorrow, trouble is I also have a wheel bearing rumbling away quite well to add to the troubles!! Not sure which one yet, sometimes I think maybe front sometimes rear but is getting worse so I will have to sort it :( I have access to a HUGE press so just gotta...

So then, what next? Any ideas? I've run it for the last few days with the tyre valves straight on the end lines from the valve block, no problems air bags stay up fine. I'm not sure what to try next, I was thinking of getting some 't' pieces to put in the air lines and then pumping the...

Well I must have spun around the wrong way or something!! When I went back out earlier closed the door up it came, took it for a quick spin to settle it all in just to see if that helped, parked it up switched it of then set up the laptop to check for faults, no faults are showing. So came in...

:D:D Ha Ha Ha!! well we will see in a minute, I've just put it back on and left it running with the door open to build some pressure, come in to make a coffee, it's F****n freezing out there!! Fingers are crossed, spun around with tongue out so just off back out to see...

Hmmm..... Gutted now, was really hoping that I had done something wrong when rebuilding the valve block, I've just re stripped it again and can't see anything wrong, all the solenoids are right, the diaphragm is in the right way around, all the 'o' rings seem properly seated, what else to...

Wammers / Irish, I think you are right, the only way to be sure is re strip the valve block and check, this was my suspision and you have backed it up! I have just read through your thread Irish along with the link to the thread you followed for rebuild, all looks like it will be very useful...

That is what is bothering me, did I get it all the right way around when I put it back together? But as much as possible I took one piece to pieces, cleaned it then refitted before moving to the next piece, but how critical is the orientation of the solenoids? I'm 99% sure all is back as it was...

Oh yes I forgot to add that it is now not showing any faults when I run the software so very confused!! Steve

Right then better do an update!!Just a quick memory refresher to save reading the whole thread to catch up again, basically the dash lights all came on for the height settings, car went into ease hard fault max 35mph. I have put on 4 new air bags, new seal in the compressor and replaced the...

Well I think I may of found the leak and the reason why the rear passenger bag would not inflate the other night.......... Looks like the new bag decided to let go of the top cup!! managed to squeeze it back on and blow it up to get it to reseat properly with my garage compressor...

Thanks Wammers, just done some more poking around on the RSW site and found the written instructions on the download software, not noticed them before or forgotten about them! have read through them and will print them out to have in the car while testing, like you say will help to check it all...