If your talking about what i think your talking about...... Land Rover havent admitted its a problem. They have said its a 'characteristic of the automatic gearbox'. Also, its not a vibration , its a resonation :) Not that it makes alot of difference to you. The older...

If your worried about SRS systems, just disconnect the battery for 20 minutes before working on the vehicle. The rest of the job is very easy.

Td4 Turbo actuators are about £30 i think. It involves undoing 2x10 nuts as far as i remember.

Just wanted to add another step for making it easier. After slackening off the lower alternator bolts and prying it away from the head. You can then remove the top altenator mount, just to give you more room and so you can see easier what your doing. Just undo the 13mm and 10mm with a...

The ladder rack is removable, as you are meant to replace it when doing the headgasket. LR released modified and strengthened ladder rack to try and reduce hgf. Its along with modified coolant pipes , modified headbolts, modified thermostat, modified headgaskets , modified head dowels...

Slots into the front of the airbox on a 1.8 doesnt it? If not, im guessing its a 'spare'.

Low pressure fuel sensor isnt on the low pressure pump. Its in the engine bay under the fuse box. Its on the fuel pipes.

I'm not completely familiar with the fuel system on the car, but wouldnt the pressure regulator have to be engine side? In the tank is only a sender, so no pump there. The lowside pump is in the wheel arch with the filter. The first fuel return comes from the HP pump. Does there have to be a...

Freelander 2 didnt launch til 2007.

Dont forget a clutch bleed. Them Td4's sometimes require a couple of bleeds before they're perfect.

What year and spec? Does the radio backlights or sat nav screen stay on intermittently after the vehicle is locked?

Td4 is far more expensive for a reason. I'd expect to get 200k from a maintained Td4 before the engine required strip to repair. A Kv6 i'd expect issues from 36k+, but then when it comes to rover engines in FL1, im a pessimist...

Hardback seal if you have a hardback. Taildoor seals not sitting properly due to wear. Taildoor water shedder - Water coming in out of the bottom of the taildoor interior trim. Easiest thing to check with a hosepipe :)

If you want cheap autobox oil. Try ringing your main dealer and see if they have it in bulk and will sell it you by the litre. If they will, take an old clean container down and get a few litres. Might work out a few £ per litre, since they buy it 1,000 litres at a time. They also wont...

There is lots of issues about with this sort of thing. It revolves around new phones constantly being brought out, which interact over bluetooth in different ways. Check out ; Bluetooth | Land Rover UK . Enter your vin, then your phone and software level. It will then tell you if your...

I'm trying to remember all the buttons on the HeVac unit, make sure you havent got ECON turned on or anything like that. With aircon switched on and auto on, i really dont think the car should mist up. I may stand corrected though.

DD ; Its the same type of roll pin, but its almost ontop of the gearbox at the back next to the wheel arch. Its a bitch to remove unlike the 1.8k which just takes alot of whacking. The one of the Td4 is designed to be removed by a special tool , which looks alot like a large version of a chain...

You can remove the gearbox with the selector still in place. Its tight, but possible. You need to lower the engine as far as it will go whilst still on its os mount. Then just twist the gearbox to lower the ird mounting end. It should come out past the wing. As for the weight. I can lift...

Or undo the 18mm bolt that goes laterally through the bottom arm and retains it into the subframe assembly. Then pry that out, gives plenty of movement to get the driveshaft out.

Interestingly enough (or not), LTB00052 doesnt mention the wierd blank connector and the foam disk. To be honest, the foam disk normally goes over the connector to stop water ingress and if you cut off the existing connector you can thread the wires through the black bank and tape them up in...