Search results

Thinking of giving these guys a crack at the Landy to make sure that the dreaded rust doesn't get established in way of the chassis. Does anyone have any experience of their services? Rustmaster and Waxoyl Professional Home Page

Woke up early Saturday to go to work and having set off in the Landy I noticed that if the throttle was partially depressed it was fine however, if I fully depressed the throttle the engine lacked all power and wanted to die. Thinking possibly a blocked fuel filter I replaced with new but...

Is it possible to change the A-frame ball joint without removing the arms and boge self levelling unit. Think it could be hard work to remove everything and difficult to reassemble on completion.:confused:

Green laning in North Wales.....any ideas??? Can anyone recommend a nice route not too challenging ie no ford/ deep mud crossings. Steep inclines yes but no water or excessive mud. Only running standard height and no breather kit fitted. Thanks.

Has anyone had any experience with these guys? Rustmaster and Waxoyl Professional Home Page Looking to have this done on my 110 this summer in preparation for the winter.

Purchased some new anti roll bars both front and back and whilst going to fit I noticed that there is no front anti roll bar currently fitted. I have replaced the rear and will fit the front this weekend. Is it normal to not have a front roll bar fitted?:confused:

Starting to see evidence of rust in way of the rear cab and want to know how to get control of it. The area in question is where the rear cab meets the main body of the vehicle. It's the strip that separates the main body and the rear cab. Any ideas?

Starting to see evidence of rust in way of the rear cab and want to know how to get control of it. The area in question is where the rear cab meets the main body of the vehicle. It's the strip that separates the main body and the rear cab. Any ideas?

When hitting say a manhole or pot hole I have noticed recently an increase in wheel wobble through the steering wheel. I have recently replaced the pan hard bushes for polybushes and check tightened everything yet still experience the wheel wobble. Any thoughts? I'm thinking possibly worn...

To me there comes a point where gearing will dictate the effectiveness of huge lift and wheels as surely such mods have a massive impact on the torque and power transfer? Or am I missing something?

Got a knocking noise from my rear suspension. I've fully polybushed the rear end and still get a knocking noise. When going over bumps especially when cornering. I think possible my roll bar bushes/ball joints are goosed so will be changing them shortly. Do you need to take the weight off the...

Just in the process of purchasing replacement bolts for when I replace the bushes on my 110. However the drawings show 2 different part numbers for both the YA185790 & YA185791. I need to know which corresponds to my vehicle? :confused:

I require a BOGE self levelling unit (NRC7050), can anyone tell me where I can get one as they appear to have been discontinued????

Just fitted CB and mounted aerial to the rear of roof above gutter only to find that the cable is too short to reach transmitter by about 50cm!!!!!! :mad:

What electrical cables run either down or along the near side C-pillar??? Every now and then I get a loud electrical noise like an electrical short. It doesn't happen often but when it does it's as if someone has shot a catapult at my landy!!! All my electrical systems appear to all be working...

I'm looking at replacing my suspension as it is 18yrs old and getting a little tired. I'm not one for serious off-roading but would like to do some green lanes etc. However, the vehicle is mainly a Tow Vehicle and as such would like a kit that best suits my needs. Any suggestions on which brands...

Going to get myself a CB and would like to hear your experiences with regards to rigs and antennas. Dont want to spend thousands but a few hundred quid for a good set-up and range isn't a problem. First of all I was thinking about opting for the thunder pole T1000 as it seamed good value but...

Fitted light bar today in readiness for next weeks spotlight purchase. I have opted for the KC 57-series spotlights as HID are out of my price range at the minute and ultimately I will fit some HID to an A-bar when funds allow. I want your opinions on which lights to fit! I mainly use the...

I have been reading the following: http://www.landroverweb.com/Pdf-files/Tuning_Land_Rover_Tdi_engines_Rev_2.pdf I feel like carrying out the stage 1 Tweeks to simply provide a slightly better off boost performance! I am going to fit a performance filter that will provide better air flow...

I'm wanting to fit a rev counter to my defender 300TDi defender. Has anyone done this and if so could you tell me how to carry out this small project. Where is the W connection on the alternator, etc???? Is it straight forward? I believe VDO are the best/std fitment to land rover!