Search results

Roasted my old ECU and looking for a replacement. Mapping not relevant. Shipping to Denmark ... Lars

Dear all, had some trouble with an ECU which roasted. Got another one for replacement (and re-mapped), and since I had the following problem. Th revs does not go down when depressing the clutch, so the switch seems to be in fault. However replacing it has not helped. There is aloo no difference...

My TD5 cut out while driving. No post warnings, just a clean cut. Cranks fine, but fuel pump only runs if I shortcut the relay. Even when the pump is shortcut the engine does not fire. Any ideas?

Does anyone know who manufacturers CV joint which has splines looking like the pictured one? It’s a 110 CSW 2001. The previous owner fitted reinforced axles and CV joints, but I have no clue who made them ... rgds Lars

I have bad rattle, and would appreciate your input. Started a year ago, gradually got worse. Replaced clutch, flywheeel, fork, release bearing etc. No change, but anything only a little worse now. Rattle when driving but really bad when the clutch is being depressed. Could it be output shaft...

Hope you guys can help me out here. I have moved a remapped ECU from a 90’ to a 110’. Only problem is that the 110 has ABS+TC and the 90’ did not. Now I have three amigos popping up and I am confident it’s because the ECU is not prepared for ABS/TC. When trying to access the ABS part of the ECU...

Can anyone help me with the dimensions of the rear (side) window cut-out dimensions? I am looking for the specific measures incl corner radius ... Thx!! Rgds, Lars

Hi there, I just recently replaced my rear x-member, having o cut all wires going through the frame. unfortunately I did not do the cutting, thus having no 'memory' of the wires were connected. Now I am re-soldering (re-connecting) all wires and realize I may have lost track of a few wires...

I may have an opportunity to get a set of door hinges manufactured in stainless steel in China. Could be interesting to see quality compared to price. The supplier is well known to our company and I trust the quality. Does anyone have drawings with dimensions on the different hinges? Rgds, Lars

I have a set of Britparts door hinges for a Defender. They all have different part numbers and are stated to be for each a different position e.g. 'left door - upper hinge' etc. How ever, (stupid me) I un-boxed them all without tracking which one goes where. Now are they really different and...

Cheers guys, I've recently bought a 110/STW whit rotten doors :o) Does anyone have experience with the AMA services and their glass fibre doors? I am very confident in the materials as I have worked in the glass fibre industry for more than 15 years. However is AMA delivering good quality...

Hi there, I've just bought a 'new' 110/TD5 replacing my 90/TD5. The 90 has a great AliveTuning remap and I now wish to swap the ECUs. Can I do this by the use of the old (first version) of the Nanocom? What is the process? Rgds, Lars

Does anyone have a drawing or chart which shows how the oil is pumped around in a td5?? Rgds Lars

Does any of you have experience with Cooper's AT3? What is your thoughts/conclusion? .. and what are you comparing with? Lars

What is the actual physical difference between the shocks: TO WA159806 and FROM XA159807 TD5 .. as seen here: Koni Heavy Track | Brands And why would the older version not fit the TD5&PUMA models? ?? Lars

Has anyone noticed that the AAP readings via Nanocom (temperature) is somewhat higher than the actual outside temperature? My inlet system is a bit longer than the standard version but I see to have some 10-15 degrees to high readings .. Lars

Hi Sierrafery! (PM notified) I recently read a note you made on making the MAF redundant by feeding the ECU with a throttle sensor voltage signal. Do you experience any kind of delay/latency related to this setup? E.g resulting in over/under fuelling? Theoretically there should be a timing...

I'm looking to fit pin-pin shocks on all four corners of my D90. This means I would have to fit front shocks at the rear corners. I am considering the Koni Heavy Track. Any experience with this and is there anything I should consider? Lars

Defender 90. I'm looking to get a bit more articulation yet keeping the ride height standard. I currently have HD springs but would like to fit +2" shocks. Preferable adjustable shocks like the KONI Heavy Track. Further I would like pin/pin on all four corners! Which kind of rear spring...

Years ago I fitted floflex bushes on my td5 90. The bushes are getting inflexible and I'm looking to fit new SuperPro bushes. However I also fitted new bolts when the floflex bushes were fitted. As I remember some of the bolts had different diameter compared to the original bolts (intended for...