Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
picked me noo one up and drove it home.
What have you done to your Landie today.
- Thread starter madfrank
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
chunkymunky
New Member
- Posts
- 9,901
- Location
- worcestershire
No pics never happened lol
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Trailpug
New Member
- Posts
- 419
- Location
- Norwich, Norfolk
Fitted new fuel tank sender realised i don't have a wire for the low fuel light!!!!
Fitted new seals on front vents so hopefully my feet will not get to wet this winter!
Fitted new seals on front vents so hopefully my feet will not get to wet this winter!
chunkymunky
New Member
- Posts
- 9,901
- Location
- worcestershire
Who me???
Big enough to live in 😃 cheap as chips?
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
Bastid
Snigger
Wanna see who finishes their project first ?
I'm starting work on mine on Tuesday
scotchgit
New Member
- Posts
- 2,777
Fitted new door locks and changed rf receiver for latest type
Diesel Do
Well-Known Member
- Posts
- 5,212
- Location
- Nottingham
Drove it! And it didn't break
top drive
Well-Known Member
- Posts
- 2,694
- Location
- Peoples republic of culter
Bought another ....
1990 g plate 3 door v8 disco 3.5 v8 on twin su carbs
Plan to tear out engine and running gear for my 90
Disco is rotten beyond belief - dropped the bonnet and bits of the chassis fell off wont have to scrap it will be able to sweep it up into the wheelie bin !
1990 g plate 3 door v8 disco 3.5 v8 on twin su carbs
Plan to tear out engine and running gear for my 90
Disco is rotten beyond belief - dropped the bonnet and bits of the chassis fell off
wont have to scrap it will be able to sweep it up into the wheelie bin !
Mark L
Well-Known Member
- Posts
- 2,693
- Location
- Tamworth - Staffs
Completely stripped down old axles from the old Disco down to bare casing. Nearly.
Came to a halt on the rear axle when I realised I don't have a 52mm box spanner. £6.25 spent on eBay should see the job finished next week.
Don't think the rear calipers have been taken off. Ever. What a sh*t bag those hex bolts were to get off!!
Both axles being taken back to bare metal and fully refurbed throughout ready to be swapped straight over later in the year.
And on that note - can anyone recommend the best method for getting in the nooks & crannies regarding the rust/paint removal?
I'm thinking rust and paint removing wheel or wire wheel on the grinder for the most of it.
Came to a halt on the rear axle when I realised I don't have a 52mm box spanner. £6.25 spent on eBay should see the job finished next week.
Don't think the rear calipers have been taken off. Ever. What a sh*t bag those hex bolts were to get off!!
Both axles being taken back to bare metal and fully refurbed throughout ready to be swapped straight over later in the year.
And on that note - can anyone recommend the best method for getting in the nooks & crannies regarding the rust/paint removal?
I'm thinking rust and paint removing wheel or wire wheel on the grinder for the most of it.
High Lander
Active Member
- Posts
- 390
- Location
- Inverness
Scraping 30 years of crud off my chassis
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
Well earlier I took the allen keys out of mine to undo the number plates on shortys and change them over to the new age related ones
discomark10
Well-Known Member
- Posts
- 3,977
- Location
- Milton Keynes
Completely stripped down old axles from the old Disco down to bare casing. Nearly.
Came to a halt on the rear axle when I realised I don't have a 52mm box spanner. £6.25 spent on eBay should see the job finished next week.
Don't think the rear calipers have been taken off. Ever. What a sh*t bag those hex bolts were to get off!!
Both axles being taken back to bare metal and fully refurbed throughout ready to be swapped straight over later in the year.
And on that note - can anyone recommend the best method for getting in the nooks & crannies regarding the rust/paint removal?
I'm thinking rust and paint removing wheel or wire wheel on the grinder for the most of it.
air will get the loose stuf, a small screwdriver, nitromorse or crust will sort the rest
- Posts
- 83,235
- Location
- Embasinga stocæ
Sand blasting attachment for a Karcher
- Posts
- 83,235
- Location
- Embasinga stocæ
Rebuilt front axle , oil and greased it. Bled brakes.
Seems that annoying "clunk" is an accumulation of tolerances. No major wear in anything , but still a lot of play on front diff flange.
Seems that annoying "clunk" is an accumulation of tolerances. No major wear in anything , but still a lot of play on front diff flange
.
