Landyfella
Active Member
- Posts
- 153
- Location
- Cambridge
Thx.
It’s a 90/110 V8 Detoxed 15Gxxxxx
Is there a parts list pdf and any rebuild manuals on interweb?
engine damage is it terminal?
- Thread starter Landyfella
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
It’s a 90/110 V8 Detoxed 15Gxxxxx
Is there a parts list pdf and any rebuild manuals on interweb?
Well that’s a bit nicer being a 90/110 engine
.Loads of free online manuals available, just takes a bit of searching.
Proper paper 1s are still available will also show up with a search.
J
steve2286w
Well-Known Member
- Posts
- 4,051
- Location
- monkeyangerland
Might be among this lot
http://smithies.co.nz/land_rover/
http://smithies.co.nz/land_rover/
Landyfella
Active Member
- Posts
- 153
- Location
- Cambridge
would this manual be correct.
steve2286w
Well-Known Member
- Posts
- 4,051
- Location
- monkeyangerland
Looks it to me
Landyfella
Active Member
- Posts
- 153
- Location
- Cambridge
Sorry do you mean looks correct?
Henry_b
Think outside, no box required.
- Posts
- 15,353
- Location
- somewhere else
Low comp 3.5 90-115hp judging by the condition of the outside and the fact it looks to have been dropped off an engine hoist from the damage sustained i'd say for £265 you got 'erm an ok'ish deal, it doesn't have any windows in the block which is nice...
I'd almost guarantee it'll be a deposite filled pile which will need a complete rebuild obvs
Kits are available..
I'd almost guarantee it'll be a deposite filled pile which will need a complete rebuild obvs
Kits are available..
Landyfella
Active Member
- Posts
- 153
- Location
- Cambridge
Already planned to rebuild it. A little ****ed off about the timing housing. They didn’t tell me about that. Crank seems to turn fairly easily which is good and bad. Not much compression. Probably seized valves. I assume they are an interference engine?
Henry_b
Think outside, no box required.
- Posts
- 15,353
- Location
- somewhere else
Yes it's interference.
Landyfella
Active Member
- Posts
- 153
- Location
- Cambridge
Having trouble finding parts on usual website using 90/110 v8. Model had the same engine pls
Landyfella
Active Member
- Posts
- 153
- Location
- Cambridge
Just seen no spark plugs in left side so will have affected compression
Landyfella
Active Member
- Posts
- 153
- Location
- Cambridge
Sadly no joy.
Are there any parts diagrams? What is this part? part of vacuum system perhaps?
Attachments
Think it’s part of the “detox” secondary air bit but am not familiar.
Try these and search some numbers.
https://www.lrworkshop.com/diagrams...gine/v8-petrol-carburetter/air-manifold_53325
https://www.lrworkshop.com/diagrams...8-petrol-carburetter/air-inlets-detoxed_53323
Believe it can be removed and plugged though.
J
Try these and search some numbers.
https://www.lrworkshop.com/diagrams...gine/v8-petrol-carburetter/air-manifold_53325
https://www.lrworkshop.com/diagrams...8-petrol-carburetter/air-inlets-detoxed_53323
Believe it can be removed and plugged though.
J
Landyfella
Active Member
- Posts
- 153
- Location
- Cambridge
It's the 'Pulsair' system.
This is as good a description as any: www.fordforums.com/threads/v8-pulsair-system.14910
Land Rover did blanking plugs to remove it. ETC6474.
Famous Four do/did a set which are just a set of grub screws. No idea as to the size, but if you remove one of your pipes you'll be able to measure thread & diameter & buy something appropriate.
www.landyzone.co.uk/land-rover/3-pipe-pulsair-detox-engine.318331/ Sadly the poster never updated the thread.
This is as good a description as any: www.fordforums.com/threads/v8-pulsair-system.14910
Land Rover did blanking plugs to remove it. ETC6474.
Famous Four do/did a set which are just a set of grub screws. No idea as to the size, but if you remove one of your pipes you'll be able to measure thread & diameter & buy something appropriate.
www.landyzone.co.uk/land-rover/3-pipe-pulsair-detox-engine.318331/ Sadly the poster never updated the thread.
Last edited:
Landyfella
Active Member
- Posts
- 153
- Location
- Cambridge
Thanks. They look just like brake unions so I think I just get some new ones and blank off use the pipes.
Ok as I was interested for myself.
Some have said they just cut and squash the pipe, a neat bodge.
These guys say they have them Range Rover V8 Petrol Pulsar Blanking Plug ETC6474 (johnrichardssurplus.co.uk)
These guys do a better looking 1 but state "not for 3 port" V8 De-Tox Blanking Plug Kit (FF006383) for 3.5 V8 Carb. Engine Land Rover Series IIA/III (famousfour.co.uk)
Whats the diff between 3 or 4? I have no idea. but maybe worth the cost of a phone call.
But looking at the first link pic, seems to have a sealing face/area.
Personally the fittings you have are the best thing you have to work with. You are not in any hurry so get 1 out and check thread size and for any sealing requirements.
As you will have the heads off (i imagine from previous posts) you have time.
See you have asked in the other fred for a size unlikely you will get a response due to its age.
So we will be relying on you.
Good luck and looking forward to the rebuild fred.
J
Some have said they just cut and squash the pipe, a neat bodge
.These guys say they have them Range Rover V8 Petrol Pulsar Blanking Plug ETC6474 (johnrichardssurplus.co.uk)
These guys do a better looking 1 but state "not for 3 port" V8 De-Tox Blanking Plug Kit (FF006383) for 3.5 V8 Carb. Engine Land Rover Series IIA/III (famousfour.co.uk)
Whats the diff between 3 or 4? I have no idea. but maybe worth the cost of a phone call.
But looking at the first link pic, seems to have a sealing face/area.
Personally the fittings you have are the best thing you have to work with. You are not in any hurry so get 1 out and check thread size and for any sealing requirements.
As you will have the heads off (i imagine from previous posts) you have time.
See you have asked in the other fred for a size unlikely you will get a response due to its age.
So we will be relying on you
.Good luck and looking forward to the rebuild fred
.J
Landyfella
Active Member
- Posts
- 153
- Location
- Cambridge
Thx. Will do although probably wont start the rebuild until later in the year. I will of course create a thread about it. Thx all
Similar threads
Freelander 1
2004 TD4 - Loom damage
