What checks have you done?

Get the biggest screwdriver your can find, then pump your arms up to 60 PSI....... AND GIVE IT LALDY or..... Get a loan of an impact driver :)

Did this on my 92 RRC a few months ago. Oh how many times I said bad words!! What a job it was trying to get the nut off, with no joy. So I ended up removing the rubber fuel hose that was attached to the steel fuel line. My trouble was I noticed a pin hole in the steel line, just at the bit it...

You can "just" see the motors edge sticking out (about the same size as the coil on the wing) through the middle grill. Get yourself some wipac replacements :-)

If the blower has gone it's a dash out job, mines has been on its way out for over a year so until it totally goes, I'm driving with my fingers crossed :)

Grills are held in by lugs, (very easy to break so have you're patient head on) get a flat head screw driver eased in top right and push GENTLEY downwards......... Should pop out. Sponge behind the grills too to catch the crude that might fly through the grills and very easy broke in two. I...

Hmmmm sounds familiar, blower (motor that powers the fan) sounds like it thinking about giving up the ghost. When you say rumbles, is it like a chopper hovering above you're Landy? ;-) How much do you know about where the blower motor is? If you get a can of spray oil or even a squirt of...

Airlock could also be the culprit. Is the Radiator cold at the top? Dirty die sels aren't my strong point, but I'm sure an airlock will have the same effect. As Wil says too, heater matrix could be blocked, but a missing Thermostat would really only mean it takes ages to heat up. A jammed...

Found this site not sure if it's of use? http://www.dingocroft.co.uk/acatalog/paint3.htm If you look at the bottom you're paint colour is there and also the part number.... Punch this into google search, and rimmer bros had mine in stock (Ardennes green) hope this helps.

Beer plus Gas? Hehe lethal combination big man! ;-)

:beer2::beer2::beer2: happy days

Dam, beat me to it ! "Rust you're nuts off" ( i think its called) is a better product, but if it's hard to find at a local factors etc, then WD-40 is better than nothing. (it has many uses other than moisture displacement)

Good luck, it's a swine to get undone if it's seized. Get some WD40 on it for a while to "try" loosen it off. You may also need the help of a friend. I had to use an oil filter tool to hold the shock itself while the nut was held. Make sure you have a spanner on it that fits....... And I mean...

It could also be the actual blower itself. The motor in the heater unit........ If that's the case, then you may be in for a bit of work as the whole dash needs to come out for a replacement.

Hope this helps. You can get the replacement part from British Atlantic as well. It's one hell of a job to get to the plug that's down behind the dash. I had to get her indoors to put her slim little hand down to undo/redo the plug. Good luck!! Product Instructions for Range Rovers

Pics?? need pics :-) even if we can't come round for a cuppa, pics will ease the pain ;-)

Locking mechanism seized? Rod corroded? Bummer to get in at, unless there's a few rusty holes to allow you to get at the rods. Possibly even get a pair of long nose pliers on it to run it back and forth to free it up more after a healthy squirt of WD . Mines was similar to this, I also found...

Looking good. Few battle scars by the look of it haha. I'd get a roof dome mounting for that CB areial as the trees will rip it right off. ;)

Haha Tony spot on the money ;) Get the pics up :)

It should have normal shocks and springs. Driving it off road select low range (small gear selector pushed forwards, it might need a good shove!) select D for most driving but yep your right about the hills going down. Lock in back to 1 ...... It still runs on a little but with a little...