Heard of the above done to sell off a knackered box before!

Have you taken the rocker cover off and checked the core plugs? I was convinced ours was from short journeys etc. Once the rocker cover was off the underside was like looking at a margerine tub. Take the rocker cover off, clean all the gunk off...

I think it is still head gasket issue, not a leak between cylinders but a leak from a waterway to say a pushrod access hole and then the sump. Possible it is being helped along by a small pressure leak from a cylinder tracking its way across the...

12.2v is a good voltage, may be an issue with the relay, swap with one of the others to test. When I was having start on the key intermittent issues I had a stand by rig of a wire from a known 12v feed with a switch in it and a double spade to...

The lower dash is just about the only area I have not been into. I could do with re sealing the cabin air flap in there. As for looking at the loom itself you may well find there is nothing to see unless there has been a big melt down. I have...

I'm a big fan of Lanlin based coatings but the chassis does need to be clean and as much as possible rust free (rust treated) first and then its a yearly thing to keep on top of it. Lanoguard is the original and there are plenty of other makes...

Have you got a good earth connection to the battery? And another good connection from the engine to the chassis? If this one is bad the electrikity will try and complete the circuit any other way it can, resulting in odd things happening.

Sounds to me like you have a short in the system some where that is draining the battery. Someone bypassed the main loom to the fog for a reason. An 86 could well have a relay for the starter under the fuses, my 1990 did. But now has a direct...

No matter which anti corrosion system you use none are a do once thing, depending on the use of vehicle, where you live it is a repeat job. I live by the sea and mine is a working farm truck, gets a good underside wash/dry then respray with...

Everything that does not get hot, or move. But make sure you do the inside of the chassis box sections as well, that is even more important than the outside.

Having re watched steamwally's video he does say it took him half an hour.[but he forgot to film it] I do now recall bit of a faff with the reverse idler in the way[ reason my box was appart was its replacement.

Now there's one, it was last autumn and I just can not remember. Sorry.

So did mine, hard to think what your issue could be.

Solder heat shrink joints are okay, but a new bullet connector and block is most authentic.

Turners do quality head gasket sets def replace valve stem seals, I would also strip the valves and springs, rockers check for any damage and lap them in, inspect head for damage/ cracks etc and order parts once

Different destinations each year. They went to Harris this year I took the club through my bit when they were here so they could get a run round the Wilks estate. I think there was about 35 land rovers as our local club joined them for the...

You may well have an "Agri spares" place near you, they will have a selection of struts used to lift open tractor windows and other access panels.

And as @marjon says do not use those blue "scotch block" connectors. There are other similar products today that work the same way today by squeezing the wire between two thin metal bits while splitting the sheath, contact area is very small and...

By the time they got to the TD5 they went back to a very chunky cast jobbie with replaceable inserts where the centre pivot and the slave cylinder pushrod go. I've had clutch problems but never the clutch fork.

The clutch fork is an item that went downhill when the coilers arrived, Series 3 had a cast item with a nylon bearing for the post. So called heavy duty [ extra bit of metal welded on the back of arm] available. Problem I have had with a...

There is no sliding any thing in. Head off, clean the surfaces of block and head, composite gasket. Follow correct torque down method. Head can be remove with manifolds on but more weight. Plumbers blow lamp is a good small heat source. Some...

Sometimes looking at an issue the next day provides the answer. :D :D

Okay so I think I've sorted this - clearly not looking properly at 11pm last night when I was trying to fit it. If you look at the sixth photo, you can just about see the stud from the mount sticking down, this was resting on the chassis leg...

Just to confirm @Hicap phill above the interior/ dash light switch as standard gives dash lights one way and interior light the other way with both off in the middle.

Could be the clutch flexi pipe has delaminated inside, result black fluid and possible blockage. Remove pipe from slave and see if fluid will flow from master.

My 1990 Ninety has both Permanent live wire and a switched one available for the lighter socket. I think how which was connected depended on the country vehicle was sold in.

As Adam Savage on MythBusters would say" Thars your problem" What about finding a scrapped even dumped trailer with a braked axle to fit to yours?

I don't think anyone is saying it isn't a thing. They are mandated for most cars drag racing if you go over 'x' speed or run 'y' time. But rarely are they a factory fitted item on most vehicles or 4x4's. And certainly never in the case of the...

What is a matter with the trailer brakes? In good order the trailer brakes will be coming on with only a normal light touch on the towing vehicles brakes. And the more weight there is in the trailer the harder its brakes should come on. Or is...

Have a look at "Steam Wally" series 3 gearbox overhaul video's on the You tube. Helped a lot when I did mine last year. There are 3 parts. May help.