The wire can corrode itself to the nozzle if left for a long time. Easy fix - cut the wire near the drum, unscrew the nozzle and pull the wire through. Put a new nozzle on.

It may be worth trying a re bleed.

Is the slave push rod the original one? Wear can be an issue.

Connections in the fuse box common issue, try cleaning them up. Old glass type?

So now : I'm going to fit 30mm spacers to the boosts 😂 Can't find tyres I like enough to justify swapping out the Insa Turbos (Michelin Crossclimate variants doesn't come in an 85 sidewall) just yet so I'll just go with the spacers. 🤷‍♀️

Spacers really are not an issue, the hub and tyre have no clue if you have spacers or different offset rims, the effect is the same. Stock wheels will rub unless you wind the steering stops to reduce lock, hence why all stock Defenders have...

Probably cold rolled, likely the most available. Strength wise not much in it for what you need, but cold has a smoother surface finish. 3mm is what I use for chassis.

hi all no more posts from me my 110 hard top letty has gone to the big garage in the sky after two cars racing hit an other car into my landy the insurance then said no more cannot mend her so im back to looking for now

STOP LOOKING, would you believe its the steering damper!!!! :rolleyes: Cheers Ian

What vehicle/year?

The only thing I have done to sort a crunched wing id replace the whole thing with a better [not new] one. However recon you are on more of a restoration than fix up. It is not hard to remove spot welds, there are special drill bits to do just...

I have done a few wings, It depends on the finish you are going for as to if it is worth the effort. In a show room truck then it is not work the effort as unless you have some serious skills, you will be riveting back together all the spotwelds...

Depends what generation, I thought they liked to split in half where the water runs down between the cab and the bed and rusts the chassis away at that point :eek:

MUD UK do a range of switches.

Hydraulic lock can only occur when water (or other liquid) enters the cylinder through an open inlet valve. The moment the piston commences the compression stroke the inlet and exhaust valves will be closed resulting in a bent con rod or rods...

Me too, I went through 3 replacements in 3 months last year before I found one that worked and kept working. A new in the box original Waxstat made one. 👍

I have had a new 200 stats that were no good, one did not open at all, best heater ever!

Thanks all sorted now 👌

The wiring looks stock and it's worked fine for years. I'm thinking must be a loose connection somewhere which might be affected by the vibration of the engine maybe. Job for another day I think.

Note that is an odd one, if switched on should go at all times the ignition is on regardless as you know. All I can think is some one has wired it wrong at some time but just a guess.☹️

Usual and best place to connect in your landy is in the right rear under the cover there. And what ever you do do not use those devils inventions "scotch blocks" to link in.

Very few require a spacer. A small number of bellhouses were machined incorrectly (too much material removed), not wanting to scrap them LR decided to add a shim (to make up the deficit). In true LR style no identification was stamped on the...

Carry on with your old type bodge method if you must, but better modern methods are available today as noted by myself and others on this forum.

Thanks folks, appreciate the welcome, meet the Wolf, picture attached :)

Yes, I can thoroughly understand why you would think that. There were times during my communications with Jake when I myself thought this is only about £50. Whilst it took a week for him to respond to my messages once he did start replying...

Having resolved my issue, secured a refund, and avoided legal action, I can now share my experience. Outlined below is a summary of the facts and that is all I'll leave you to draw your own conclusions. On 6th February, I ordered a Marshall...

I think you should be fine with any 300tdi intercooler, I believe they are all the same. However I am not an expert in correct, I am more along the lines of what works, I have an aftermarket 300tdi intercooler fitted to my 200tdi engine. The only...

Model and year may be helpful.

exactly like in the picture

Sounds like the type fitted to 1980 and on Series and 83-85 Coil spring models.