23 Posts ago. I like to post a few about me tratter now and again. (As well as reminding Freelanderers of their inferior mode of transport :p). I like it here on the Beano page where it belongs 🤣

Shame that a certain person has come on here to hijack the thread and have a bash at others, having done the same in spades on another thread, which I am sure some of you will have seen. He obvs wants this thread to be moved to AG so he and his...

Nite

Just ordered some more nuts for me friends.

No. Fings from near the bread int sainsberrys.

Is that another two country buxom beauties 🥰

This ain't the thread for whatever axe it is you have to grind Gratch. Take it elsewhere please.

I probably will replace it. It dosent feel bad when tested.

Many people say that once you have got that far it is false economy to not change it. Well done on getting it out. Thin k of the money you have saved!! (Could spend it on a noo flywheel!;))

Hello. I got the gearbox and clutch out. Not a hard job just a bit fiddly with lots to remove. I made the landrover tool from the manual to fit gearbox and fitted it to my gear box jack. Removed gearbox and transfer box as one. Clutch has had it...

You can make a tool with a flat bar of steel. cut a short piece off, drillholes so that you can put a nut and bolt in one about 6 to 8 inches up the long peiec, and a corresponding one in the end of the short piece. So you are left with a Y...

Well, sometimes I feel like saying "I don't know where today has gone." Today I did say that to the neebs who has just fed me! I said that I had to go as I had to feed the dogs and get myself off to the farmer's market. At which point they told...

You can't really, except by editing them to empty then leaving a full stop. It might be nice if you told us how you sorted the problem out, it may help others in the future.

have you seen how much they are o_O:)

Mornin all. I woke up to a very pleasant message from someone and a lot of much unpleasantness from a load of others, although support from one who does "get" me. So the usual crowd, plus one new unexpected member of the gang. Then I go on...

Morning All. :D A better day weatherwise. :) Foot hurts again. :( Have a good day. :D

Avvin 2 crumps then going to bed. Not seen kev ferra while. Naybor ain't seen im on is wildlife camera ferra week.

We have had a change of ray-geem in certain area's. Fings chucked out to stop us hurting ourselfs. Or correcting the way they fink we should be wukkin, but dun't know wot we does. The peep doing the chucking ain't responsible fer making money so...

You seem to “borrow” a lot of stuff from your work 🤔. J

No FLs have to buy it in 2 bits front and rear subframes. J

Me hevva cutting looks like its failing so eye has hadda nuvva go. This time pulling the blue and purple flower oft. While taking a cutting earlier eye were quite pleased to see about 8 bee's hoverin on and around me hevva. Tis why eye bort it...

Eye is poorly. Feller sheep on me bed last nite wotchin youtube. Bin wukkin too many hours this week. Woke wiv a sore froat 3 or 4 hours later. Woke int nite to find eye hassa cold. Baked beans and pizza fer tea as eye can't be bovvered wiv me...

Fake news. When have yer ever seen a fred on ere asking where's the best place to buy a new chassis. Norrin the Freelander section.

That's the trouble with FLs the rust spreads every where

Need to sort me gate out. Noticed a mark at the bottom where the powder coating is cracked. Pulled oft to see it rustin like a tratter. Going to wire brush it and use vactan to kill the rust. Got meself a free rubba mat to lie on from wuk. Ses...

Did me tratter service this morning. And got the grease into the last of the four UJ's, using a bigger grease gun. And - didn't spill any sump oil or get any shooting up my sleeve (apart from a couple of unavoidable drips). Seven litres of...