Me & my wife had 4 Covid jabs each. No ill effects, although I did get covid after being in Cologne in May 2022. Main impact was on our Canaries holiday the week after. couldn't taste food properly & dull ears. Sorted that out back home...

I suspect you are correct Keith (hence why I said "assumed" above !! ). Most docs are vague onb it, but "GEMS by Poole" document says this, but that could be a resistive divider with or without correction. Correction of non-linear output could...

Pin-1 should be supply voltage. A1-6 connects via RL12 to 12V Pin-2 will be the MAF output Pin-3 goes back to the ECU Ground via A1-9. Assuming no electronics inside the MAF, you should see static resistance across pins 2 & 3 (maybe 1-2 as...

Google AI says 2.5ohms to 3.1ohms across pins 2 & 3. Diagnostics should show airflow readings, but not sure what values are expected. range rover p38 v8 maf resistance

:banana: :banana::banana:

Best sort the battery drain. Otherwise depending on sunshine at you local area, get a solar panel, or one of these Noco Genius chargers. I could not get enough sun due to local trees, but that Noco kept my Blue P38 batterys until I fixed the...

Now that would be a good idea @MGT. Ignoring for another week now.

Najlepiej byłoby, gdybyś skorzystał z Tłumacza Google z polskiego na angielski i zadał swoje pytania po angielsku. W ten sposób możesz uzyskać więcej odpowiedzi.

Just unplugged the amplifier connector, and put that bypass plug into the loom. The connector we used was taken from a non-working amplifier we got on eBay. We removed the amp as well to make some space, but that's up to you.

Nope. either way round.

Don't know what the classc pipe routing is like, but I did the rear pipes on both my P38's. Roll of copper-nickel pipe, fittings & flaring tool. Hardest part was feeding the L-R pipe over the rear crossmember. The P38 have a joint behind...

That's usually the stud turning in the plastic housing. I replaced one with an allen bolt, so I can hold it from underneath while tightening the nut.

Apparently britcar.com has 8 in stock. IMHO they just get in the way of regular maintainence on most cars.

eer yes, lots of it. Without the spring, the compressor will be all that's holding air in the bags !!

It would need all the security stuff copying into the Highline. There are places that can do the cloning. Also unless they relicate the mileage (kilometerage ?) then the Instruments or BECM will update to whichever is higher. If you have...

They should sit on the slightly larger section of the tube, resting against the flange. Then make sure they seat into the recess in the valve body top half. Stem should seat like this (not my fingers. They are PaulP38's)

For all that effort, why not look at using something like the L405 sensors, which output a voltage from 0.5-4.5V ? They would probably just need modified brackets & arm length to get the correct voltage range ?

P38 Undertray ?? Never seen one, and neither of mine have them.

The momentary relay only has to be on for enough time for the P38 FOB transmission to unlock or lock the car. i.e. press & hold momentary fob, while you use the P38 fob. Then release both.

Most likely it's one of the two o-rings on the bottom of the valve, or the thin o-ring around the plunger body. i.e. one of these three :

https://www.landyzone.co.uk/land-rover/rf-reciever-work-round.258096/

Shame you didn't ask yesterday. I could have checked the colours on mine !! Not 100% sure, but RAVE does have G, R. B. Y, etc. for the connectors ? U = Blue in the rest of the wiring diagrams, so probably Front Fogs..

Definitely too many faults reported. Cannot believe two airbags & two crash sensors have all failed ?? As above check the diagnostic connector for corrosion. Also check the SRS Bulbs in the cluster. There are usually two, & if one fails...

The rear airlines are much harder to get into the airbags than the fronts. Maybe they are simply not fully seated ?

If the FL1 originally had the standard HK or Becker, then the head unit feeds to the amplifier are Line Level, but use the same pinout as aftermarket speaker outputs. My bypass plug simply connects the 8-pin wiring from the head unit directly to...

Why did it require replacing ??

On my Son's FL1, we had to bypass the HK amplifier under the left seat. I mad a bypass plug to go into the loom, and then the aftermarket stereo feeds the speakers direct. See post #4 in this thread...

+1 on try the tailgate trick. If where you park makes that a bad idea, you could take Fuse 44 out, which has the same effect as removing the relay.

10.2v where? At the battery or at the starter motor?? Either way it seems low to me.

Yes but any repair workshop could probably weld a replacement in. Cost vs replacement P38 depends what you want. Yours was getting rusty before the accident anyway. If you don't want to repair yours use it as a donor car for a cheap P38.