@Anaconda - Take a look at these two links which describe what GLASS does and lists some member benefits, other than access to TrailWise of course: https://www.glass-uk.org/why-glass.html https://www.glass-uk.org/members/public-discounts.html

Had a Quick Look and there are reports of that track been private & police were there turning bikes around a few years ago. Off again to see who owns it & polite emails may be sent

I keep finding routes like this and look around to see if there is ways through. Think I will need to spend some time on council ROW sites. Plenty of practice on the wilts one

Yeah, it's the main reason I have a GLASS membership

You can drive that lane up to Claerwen reservoir. You can drive the lane running round the top of the reservoir but it's a dead end as far as I am aware, even though there is a non described track at the end .

Do you still get trail wise through GLASS membership?

I like Trailwise - it's especially handy for the comments against lanes with the condition, whether they're suitable for 4x4s, and hints/tips for driving them. It shows BOATS and UCRs with usually up to date info about TROs and TTROs. It's...

Wiltshire to Harlech/north wales over 4 days. Looking over some routes and round Builth wells and they are dead ends. Other problems I will have is I may not have drove/seen these lanes before Does the outdoor active show unclassified roads...

You can put a grease nipple into you drip arm before fitting. May help in making them last longer

Have read about it but just going to swap like for like.

And now from our roving reporter in Benfleet......... A long-haired, wild-eyed man was seen screaming through the streets of Benfleet today in a Grey Mini classic while proclaiming "She Lives, professor, She Lives". :D At long last I seem to...

I am planning a good few days away with 2 other motors and was wondering what methods/apps/clubs do you all use. I am using OS to lay the route but these do not show unclassified lanes.(trying to link up dead end byways that look like they...

Do the glyn Lewis drop arm conversion. Bit more expensive but easier in the long term to change

My 200 has a cheap facet copy pump off ebay, starts and runs just fine without it, but I can notice a power loss up long hills if not switched on. I think the lr mech lift pump is fine when working, but when it pack s up it actually causes a...

But a 1/4 chassis would replace them legs(&rot)

As above ^^^^ They are drain oles arent they? In which case a good brush/prod and some protective treatment inside &out could help hold it off for a while. But whats going on on the inside is harder to know. Is that the rear feul tank? dont make...

My 200 does not have the mech lift pump. It runs an electric pump(110 v8 petrol 1985) Now fun bit… my motor will run without this pump been turned on,happily sit at 60mph for over an hour & not show any signs of restrictions. I know this as the...

For anybody passing the Greendale Farm Shop twixt Exeter and Sidmouth tomorrow, Sunday 16th Feb, the main car park is dedicated to landies and all things landrover from nine until noon. You can officially show your landie for a fiver.

Morning mate, will likely be MS I think. More to try and make it reliable and get the timing a bit more tuned in. I’ll also be looking to add a more aggressive cam, manifolds etc and hopefully I can map to suit this. Nigel - mr megasquirt...

If its the intank pump fitting the tank I think they are the same fitting too. If you have the wires in the loom you mayalso have a spare space in the fuse box for a fuse and relay? Basically, anything past the 3.9 does away with the dizzy. the...

I’ll have a look mate. I was thinking same as Phil. Your correct, 300 does just have sender but I think in tank pump is same thread as sender. Will soon find out. The loom looks identical but I’ve got a full v8 loom on way from an ES so tempted...

I thought tanks were the same, plastic tank with different screw pumps

Thanks but I'm not that way inclined 👬

Feeling the luv ya big trucker. 😘 🤣🤣

Evening all… Sending hugs & kisses to you all on this love day.

its hard to see on the picture but theres a piece welded to the round bar that i've outlined in red. The pin in the fixed upright is holding it in the open position, pull it out and when closed, it fits in the other hole below it. 10 seconds to...

Iv been past RPI near Norwich twice this week & saw some nice classics RR outside with big 3” exhaust pipes. The SIL is running megasquirt on the forward control. This was out on the road the other week,says safer to fix than flapper/hotwire...

Yeah have to send exchange as they don’t keep them in stock now. 8-12 weeks turnaround I think she said. I’m just going to have a bottom end from them and build myself as built petrol engines before. Albeit with 4 less cylinders. Seems quite...

Looks good. How did you decide to keep the bull bar upright?