D

diko93

Active Member

• Jan 23, 2014

• #1

Im looking for a replacment carb for my 2.25 series 2a the fuel feed pipe threads have stdipped out of my carb whats the best thing to replace it with?

 

dominicbeesley

Well-Known Member

• Jan 23, 2014

• #2

Weber 34ICH are ok, if you can be bothered fabricating a throttle cable and air feed DMTL32/34 as fitted to defenders give more power _and_ better economy. If you're flush you could go for an SU from ACR. Or you could just fix the current one? You might be able to bore out the threads?

 

D

diko93

Active Member

• Jan 23, 2014

• #3

I gave seversl su carbs with the right needle and jet I could give that a go I like the webber but cant afford itd price tag the metsl in the carb has jyst pasded it I dont ghink it would stand to being bored think ill have a look at an su set seen as I allready have some

 

oxides

Well-Known Member

• Jan 23, 2014

• #4

Can you get the carb body helicoiled? or is it some bloody stupid thread?

 

wickford90

Well-Known Member

• Jan 23, 2014

• #5

diko93 said:

I gave seversl su carbs with the right needle and jet I could give that a go I like the webber but cant afford itd price tag the metsl in the carb has jyst pasded it I dont ghink it would stand to being bored think ill have a look at an su set seen as I allready have some

Click to expand...

Are your fingers ****ed, or you typing in Welsh.

 

D

diko93

Active Member

• Jan 23, 2014

• #6

Presume its a daft thread havent checked tho, and no im just **** at riting and dislexic so struggle doesnt matter s long as ya can understsnd it

 

Oldseadog

Well-Known Member

• Jan 23, 2014

• #7

The SU is a good carb for a 2 1/4

 

D

diko93

Active Member

• Jan 23, 2014

• #8

Im hoping so

 

B

barleywine

Well-Known Member

• Jan 23, 2014

• #9

Could it not be repaired with epoxy metal.

 

D

diko93

Active Member

• Jan 24, 2014

• #10

Unsure epoxy may work however im not over keen on bodging fuel pipes over the engine

 

ronsealdeath

Sagging Member

• Jan 24, 2014

• #11

If its a zenith buy a knackered one off ebay and use it for parts. Forget a used 34ich they clog beyond repair if not filtered well in their life.

 

MigGames

Member

• Feb 2, 2014

• #12

Bit controversial this but i personally would give a Zenith copy a try.
I have on my FFR a Allmakes 36IV Copy which was abut £40 shipped and apart from a few poor quality brackets and clips has been spot on for about 6 months use.
I didnt expect much but for 40 quid it has been a good buy.

 

ronsealdeath

Sagging Member

• Feb 2, 2014

• #13

MigGames said:

Bit controversial this but i personally would give a Zenith copy a try.
I have on my FFR a Allmakes 36IV Copy which was abut £40 shipped and apart from a few poor quality brackets and clips has been spot on for about 6 months use.
I didnt expect much but for 40 quid it has been a good buy.

Click to expand...

I had one and it was poorly made; accelerator pump was faulty from the get go. But they are cheap. The weber is a quality carb and only £100 which is fair I reckon. If you get a decent zenith copy then all good.