jai_landrover

Well-Known Member

• Oct 13, 2012

• #1

Righto I have a plumbing issue on my mota.

I have 1/2 inch bsp for all my oil pipes inc remote filter. However my 200tdi oil cooler has 20mm metric male thread for the in;et and outlet. I know I can order adaptors online but I need adaptors tomorrow (Sunday) ideally maybe Monday morning first thing from Pirtek if nothing else but ideally tomorrow.

These are the bits I need priced silly:

LAND ROVER DEFENDER DISCOVERY RR -200tdi OILCOOLER ADAPTORS | eBay

Does anyone know If the adaptors for 3.9 oil cooler in rads fit the thread in the 200 rad???

these:
NTC3858 COOLANT PIPE ADAPTER | shop | www.lrseries.com | L. R. Series

Anyone got any Ideas?

Screwfix, Tool station, Wickes or anywhere I can get them from??

Jai

 

pressbrake

Well-Known Member

Forum Sponsor

• Oct 13, 2012

• #2

Have you access to a lathe, or both types to make an adapter and silver solder together

 

3.5 efi

Well-Known Member

• Oct 13, 2012

• #3

jai_landrover said:

Righto I have a plumbing issue on my mota.

I have 1/2 inch bsp for all my oil pipes inc remote filter. However my 200tdi oil cooler has 20mm metric male thread for the in;et and outlet. I know I can order adaptors online but I need adaptors tomorrow (Sunday) ideally maybe Monday morning first thing from Pirtek if nothing else but ideally tomorrow.





Does anyone know If the adaptors for 3.9 oil cooler in rads fit the thread in the 200 rad???



Anyone got any Ideas?


Jai

Click to expand...

got both in the shed and will go check for you now even though it's freezing and I'm half cut. back in a mo.

 

Pikey

Dummy Ejection Facilitator..

• Oct 13, 2012

• #4

you int gonna get owt like it from normal hardware store. closeest you'll get is 1/2" to 22mm compression or 1/2"" to 22 Tap connector.

 

Allyipod

Active Member

• Oct 13, 2012

• #5

lzir 3.5 has fell over in da shed and cant get up...lol

 

jai_landrover

Well-Known Member

• Oct 13, 2012

• #6

Cheers Everyone!!

Hope he is ok Or Copiously Drunk!!

 

jai_landrover

Well-Known Member

• Oct 13, 2012

• #7

have a lathe worse case is Pirtek Monday morning but was hoping to get running Tuesday and still need to sorto out a banjo bolt from an old P4 rover PAS box and the water hoses.

 

3.5 efi

Well-Known Member

• Oct 13, 2012

• #8

Allyipod said:

lzir 3.5 has fell over in da shed and cant get up...lol

Click to expand...

did you see that. was hoping nobody was watchin.

Jai, they're the same fit into the rad (was a 300 rad but guess they'll be same on 200). took the ones out of the 3.9 rad and will post monday if you pm your address.

 

jai_landrover

Well-Known Member

• Oct 13, 2012

• #9

3.5efi Well done cheers for that. hope you never sustained any injurys while checking.

Hold off with the postage for now but really much appreciated. I may have a source here with a dead 3.9 rad so will try that first might be able to get it tomorrow morn will keep you updated. I owe you a beer tho Mr 3.5efi info mucho appreciated!!

Jai

 

3.5 efi

Well-Known Member

• Oct 13, 2012

• #10

no problem mate. will cost maybe £2 to post, just post the others back when you get them out.