henryp · Jan 11, 2010

hi all,
this has probally been covered alot, but i need some help..
picked up my first landy today, and the heater was fine. but i just went for a drive with the mrs, and i tryed to make it abit cooler, then it just started blowing cold air. and moving the level doesnt effect the heat and it also started blowing on her leg which it wasn't before and i cant seem to stop it coming from there...? lol im useless..

cheers
henry

jamescronin · Jan 11, 2010

Are the leavers moving the leavers ontop of th heater box? - will be a 2 person job to work it out - maybe that the cables ahve become loose from the levers ontop of the heater box ????

tombardier · Jan 11, 2010

the heater box is under the bonnet, in the back corner on the passenger side. Make sure the cables on top of that box are moving when you operate the controls.

bustersbus · Jan 11, 2010

If the cables are nice and secure on top of the heater box, then it might be where they fit on the levers...

and this'll be the heater box....

and where the cable is on the top...

There's also another down the side of the heater box

sypher · Jan 12, 2010

Like good ol buster said , just to add - the top cable on the box controls heat ( if you can call it that ) , and the side cable controls direction ( floor - screen ) .

( Muppet I bought mine off had theses all to cock back to front and alsorts )

Half hour max to do it ( unless your controls/cables are screwed .)

.

bustersbus · Jan 12, 2010

sypher said:
Like good ol buster said , just to add - the top cable on the box controls heat ( if you can call it that ) , and the side cable controls direction ( floor - screen ) .

( Muppet I bought mine off had theses all to cock back to front and alsorts )

Half hour max to do it ( unless your controls/cables are screwed .)

.

Nearly right sypher mate

The metal outer cable nearest the bulkhead works the flap for windscreen and floor....

Ye can maybe just make out the cable in these photies...

Can't remember off the top off me head just now what the other cable in the furst photie does but there's a cable on the lever on the fan speed side...

henryp · Jan 12, 2010

cheers for the replys lads, i'll have a look after college

henryp · Jan 12, 2010

just been and had a look, somthing is up with the cable as it doesnt seem to do anything. but i just pushed the lever in the engine bay so its perma on. ill strip it down n fix it when i get home

thanks again lads

sypher · Jan 14, 2010

bustersbus said:
Nearly right sypher mate
The metal outer cable nearest the bulkhead works the flap for windscreen and floor....
Ye can maybe just make out the cable in these photies...

Can't remember off the top off me head just now what the other cable in the furst photie does but there's a cable on the lever on the fan speed side...

I was on about the cables on the heater box itself

( not the controls he he he

.

The other cable ( on the fan switch side ) closes the flap on the bulkhead directly behind the heater matrix ( could be classed as a wading flap LOL

)

.

bustersbus · Jan 15, 2010

sypher said:
I was on about the cables on the heater box itself ( not the controls he he he .

The other cable ( on the fan switch side ) closes the flap on the bulkhead directly behind the heater matrix ( could be classed as a wading flap LOL )

.

HEHEHEE! Ah gets ye now mate

Ye'll be on about the one ye can just see inside the heater behind the seal...

buckshot · Jan 15, 2010

bustersbus said:
HEHEHEE! Ah gets ye now mate
Ye'll be on about the one ye can just see inside the heater behind the seal...

ere buster ya durdy bastid look at the state of that floor!

dont the tight scotish purse string run to a dust pan and brush FFS!!

:hysterically_laughi:behindsofa:

bustersbus · Jan 15, 2010

buckshot said:
ere buster ya durdy bastid look at the state of that floor!
dont the tight scotish purse string run to a dust pan and brush FFS!!

:hysterically_laughi:behindsofa:

FFS! Ah hadn't finnshed what ah was doin' mate

Besides, it's hard tae keep an old sandstone floor lookin' clean

buckshot · Jan 15, 2010

bustersbus said:
FFS! Ah hadn't finnshed what ah was doin' mate Besides, it's hard tae keep an old sandstone floor lookin' clean

lol if ya could see the floor whenever i do stuff in me mates workshop you'd have a chuckle

my old man says i'm a mucky bastid sure i'd **** then sit back down in it
:hysterically_laughi

bustersbus · Jan 15, 2010

buckshot said:
lol if ya could see the floor whenever i do stuff in me mates workshop you'd have a chuckle my old man says i'm a mucky bastid sure i'd **** then sit back down in it
:hysterically_laughi

HEHEHEHEHEHE! Aye, ah'm a bit like that mesel' anaw

My worst thing is not puttin' the stuff ah've used away again. Ah've got tools in small piles all over the place dependin' on what job ah was doin' tae the bus at the time!... but ah know where tae find thum again tho'

buckshot · Jan 15, 2010

bustersbus said:
HEHEHEHEHEHE! Aye, ah'm a bit like that mesel' anaw My worst thing is not puttin' the stuff ah've used away again. Ah've got tools in small piles all over the place dependin' on what job ah was doin' tae the bus at the time!... but ah know where tae find thum again tho'

got meself a new halfrauds pro socket set the other day when i had to replace the starter on the old 90 , and vowed to keep it clean and tidy i did keep putting the bits back in the box but soon got fooked off with that

well the way the whole job went i nearly torched the whole lot and took up golf at 1 stage

henryp

New Member

jamescronin

Active Member

tombardier

Well-Known Member

bustersbus

Well-Known Member

sypher

Well-Known Member

bustersbus

Well-Known Member

henryp

New Member

henryp

New Member

sypher

Well-Known Member

bustersbus

Well-Known Member

buckshot

Well-Known Member

bustersbus

Well-Known Member

buckshot

Well-Known Member

bustersbus

Well-Known Member

buckshot

Well-Known Member

Similar threads