S

Seahawk

Member
Hey all

I've got yet another ID parts parade! Hoping someone will take pity on me because I'm at a total loss on this one.

I've got a 1986 Defender 90, which was modded when it came to me so I'm having a tough job figuring out what is what. Having completed the rear axle, I'm now at the stage where I'm overhauling the front axle.

I know the rear axle is Disco 1, and I thought the front axle was original Defender based on the brake calipers and info that I had, so I ordered a replacement Defender to KA swivel ball kit from Paddocks (http://www.paddockspares.com/da3167-swivel-kit-front-axle-to-ka930455.html).

However, now that I've stripped the old swivel ball off, I've realised that they are not the same at all. The main difference seems to be the upper pin which on the old part uses a bearing, whereas the new part is in a shaft with some kind of fibre-based collar. Also, the race that the old shaft sits in has a bevelled outer, again totally different to the new one.

I've taken a couple of photos of the old part. Looking at Defender, Disco 1 and even Range Rover upper swivel pins I can't find a match at all.

Is it just that the replacement parts for these are supposed to be different to the original? Or have I got some crazy oddball / mashup axle on my hands.

Any words of wisdom would be wonderful.

Cheers

Marcus

2015-12-12_1935.png
 

Attachments

  • IMG_4180.jpg
    IMG_4180.jpg
    153 KB · Views: 210
sounds like you've got a 24 spline rear axle and a 10 spline front one so you've got a bearing on the bottom and a raiko bush on the top
 
it is abs it would be from a disco possibly same as rear ,probably fitted to your early defender as the 300 tdi axles onwards have thin drive members to allow for alloy wheels,the chrome ball itself will take the pre 300tdi rialko bush as would have been fitted as std though im unsure if actual swivel housing will take the defender top pin
 
Thanks for the quick replies guys.

It is a 24 spline halfshaft.

The DA3167P kit is the one that I bought, which seems quite different from the original.
 
No worries Marmaduke. I've got it all here in front of me and it's pretty confusing!

Reckon I have a total mix of stuff on this axle because the brake calipers look like RTC4999 and RTC4998 :/
 
Thanks James, I think that's the ticket for the swivel.

Just got to figure out the brakes next. They look like RTC4999 and RTC4998. Would that make sense, given that the previous owner wouldn't have wanted to put ABS calipers on it?
 
Seahawk said:
Thanks James, I think that's the ticket for the swivel.

Just got to figure out the brakes next. They look like RTC4999 and RTC4998. Would that make sense, given that the previous owner wouldn't have wanted to put ABS calipers on it?
Click to expand...
are you after new calipers or just parts
 
Sorry should have been more specific - I have already bought RTC4999 and RTC4998 calipers (the old ones were properly seized). I just want to make sure they're the right ones.
 
as long as the 2 caliper securing bolts are a snug fit in caliper and you have just 1 pipe port it wont matter what calipers you fit
 
Just when you thought this thread was done...

So it seems I have some oddball hubs too. Anyone able to ID these? I can't find anything similar, with the recessed nuts.
 

Attachments

  • IMG_4190.jpg
    IMG_4190.jpg
    245.1 KB · Views: 174
You must log in or register to reply here.

Similar threads

Officerdibble
Swivel housing inner gasket
Replies
7
Views
460
Def90man
Def90man
A
Swivel ball part number
Replies
1
Views
495
Aydencj
A
A
Disco 1 swivel pin
Replies
6
Views
993
Anaconda
A
dag019
Refresh my memory - swivel rebuild
Replies
4
Views
1K
dag019
dag019
B
rear axle
Replies
1
Views
795
jai_landrover
jai_landrover