everlatesparky

Active Member

• Nov 14, 2011

• #1

Yes my ABS is ****ered!!
Self inflicted this time
Was using a hub puller to remove the NS hub so i could change the diff......yes you guessed it i forgot to pull the ABS sensor out....plonker..
Crushed the end of the sensor big style.
Replaced the sensor but now got the ABS fault showing on my display.
Code's are :-
080056 Brake switch failure......brake lights work ok!
08010 No voltage at pin 1 ECU when ignition on
08014 Front right wheel air gap too large.....Puahed sensor in till it touched reluctor ring and then pulled back about 1mm...no change
08016 Front left ...as above
08056 Front left wheel sensor open circuit....new sensor fitted still same.


Let the abuse begin

 

lowfat

Active Member

• Nov 14, 2011

• #2

Brake switch does more than the Brake lights.... Easy to change.... rest of it no idea

 

SpudH

Well-Known Member

• Nov 14, 2011

• #3

You've blown the fuse for the ABS, change it and rescan for faults

 

everlatesparky

Active Member

• Nov 14, 2011

• #4

Not quite that thick spud....fuse is ok!

 

SpudH

Well-Known Member

• Nov 14, 2011

• #5

everlatesparky said:

Not quite that thick spud....fuse is ok!

Click to expand...

Didn't mean it like that Sparky

The last time I was having trouble clearing ABS faults the 'no voltage at pin 1 in ecu' was one of them. Turned out to be the fuse.

 

wammers

No longer with us, RIP

Donater

• Nov 15, 2011

• #6

Sensor must be pushed in until it touches reluctor ring and left where it is. Air gap will be set when wheel turns.

 

Propman

Sheikh Le Freak

Full Member

• Nov 15, 2011

• #7

Can I ask what RR you have?

Not to worry, I checked in your profile. :doh:

Have you checked that all relays and fuses are working?

(Apologies if teaching to suck eggs)

The ABS electrical system, has relays and fuses located in the engine bay fusebox.

• Relay 2 (yellow) - ABS valve relay.
• Relay 15 (green) - Ignition relay - ABS power
• Relay 17 (black) - ABS pump relay
• Fuse Maxi 3 (40 amp) - ABS pump relay
• Fuse Maxi 24 (5 amp) - ABS ECU - Ignition supply
• Fuse 27 (30 amp) - ABS ECU - Battery supply.

080056 Brake switch failure......brake lights work ok! ..... The switch is factory set and should require no adjustment. So, it's either a faulty switch (doubtful as you've said the lights work) or a blown fuse (plausible)

08010 No voltage at pin 1 ECU when ignition on ..... Check Fuse 27

08014 Front right wheel air gap too large.....Pushed sensor in till it touched reluctor ring and then pulled back about 1mm...no change .... As WAMMERS states, clean sensor tip, insert fully and forget about it.

08016 Front left ...as above .... As above

08056 Front left wheel sensor open circuit....new sensor fitted still same. .... I can only suggest you re-check the fitting of the new sensor, was the wiring damaged in anyway? Check cct Fuses/relays then re-check cct again once fault 08016 has been rectified.

HTH

 

Last edited: Nov 15, 2011

everlatesparky

Active Member

• Nov 15, 2011

• #8

Thanls for replies gents......more bit's to look at!!!!

Will post verdict if i find ome

 

Propman

Sheikh Le Freak

Full Member

• Nov 23, 2011

• #9

Have you had any joy with this?