Search results

Hi, Need some advice, on a 200tdi the lower thermostat housing bolted to the engine block can you remove it without taking off the water pump and timing case? I need to replace the gasket but it looks so tight to do so. ????

Hi All, Need some advice, my engine on a 200TDI defender 90 is a 11L 17377A, with the BritPart service kit I got a crush and a solid copper washer for the oil pan plug. Which one should I use? Also is it just me or doing the oil pan plug up is very stiff..!!! ? seems cross threaded but had the...

Hi, can you help..... Since I bought my 90" the engine oil pan plug has always leaked from the plug in the past being cross-treaded. Over xmas I am looking to take the oil pan off and as a "Plan A" tap it out to see if this helps. But i am not sure what tap size i would need, can anyone help...

Hi, following a fluid change on my LT77 gear box I have developed a leak on the drain plug. I can’t remember if there was a copper washer there but on the parts diagram its doesn’t show any. Is this correct ??? When I looked up parts for the LT77 I see on eBay that people sell a kit with a...

Hi All, After some advice and help, I am making up a temperature monitoring system that in the cab displays the temp of the Engine Oil, Transfer Box Oil and Gear Box Oil. Being in the electric industry I am fine on the electric side but need help on what temperature sensor I should use and...

Hi, I would like to add to my custom dashboard gauges that show the oil temperatures for the engine, gearbox and trans. Does any know of good locations to install the temperature sensors at each of the three locations?

Hi, So, following filling up yesterday I noted diesel leaking onto the floor... it turned out to be diesel coming out of the fuel sender meeting the tank. I took it all apart, cleaned each surface and refit it but the tabs on the tank that hold the fixing plate on just bend up... poor design...

Hi, Would anyone know the part Nos for items, 9 - 8 - 7- 6 - 5 please.

Hi, Need some urgent help guys.... So 3 weeks back I parked up my Defender and went about replacing my rear stub hubs and bearings. And to do this took off the drum braking assemble in one go and hanged these up on the springs to save touching the braking lines and draining down the system, it...

Hi, Would anyone have a PDF copy of the noted workshop manual that they don't mind emailing me? It would be much appreciated.

My rear axle to my 90 Defender, K reg is 22S 13141B…. replacing my bearings I noted that when removing the old bearings an outer oil seal was installed (No 12). But looking at the LR Workshop manual being a 90” these are exempt. It could be that the last person to have it installed them by...

Hi, From the stamp on the outside of the Diff ( HRC 1124 ) & ( A-15L-F ) can you tell from this if its a 2 or 4 pinion Diff ??

Hi, I can't find the serial number for the front axle (but found the rear axle)... i am not sure if the past owners have replaced it or not but need to order parts for it. Its a 1992/93 Defender 90, is there any way to find out were it sits in "Change Points" in regards to ordering parts? Is...

Hi, Can anyone tell me how you fit these brake pad springs please?

Hi, Need a little help on gear box oil please, can I use Dexrox 2 oil that I use for the transfer box in the main gearbox? The manual says use ATF oil to M2C33 but can’t find this nor dose Halford sell it Any help would be great.

Hi, The replacement o ring that goes into the case for the intermediate shaft i can't get it in as its just to big. I have checked the Ref No and its the correct new o ring i have. Any help on this... do you some how shrink it to get it in?

Hi all, Need some expert help on this one.... so watching youtube and reading the service book can i have a 2nd opinion please. For the intermediate gear spacer tension am i correct that you need to do: 1 - Tighten the nut to take out all play in the gears and measure the preload as per the...

Hi, Taking off the handbrake housing from the transfer case i see there is a gasket behind it... its not in the RTC3890 gasket kit. Would anyone know the part number for this gasket please? (Photo attached) - Tans Box is LT230 T (22D type)

Hi, Can you anyone tell me if there is a gasket for the LT77s gear box to the transfer case (photo attached). If there is would you know the part number?

Hi, Quick question... do you need to use threadlock on the bolts holding down the cylinder head? Replacing the head gasket this morning.