tyregeezer's latest activity

Landrovers together in front yard still have under trays and wheel arch liners/trim to fit, discs/pads and have a leak off pipe leak to do, abs off to ecutesting.com for repair will bleed and do brakes on its return with ap200. Back on 07...

Messing about with last few jobs before moving it out of the workshop, autobox arm to cable had seized so stripped cleaned and soaked in oil for a bit works fine now, had a power steering issue but seems to have resolved itself think it must have...

Also found this ref abs https://electrouniversity.com/how-to-test-a-abs-sensor-with-a-multimeter/

Great pleasure my friend , just hope it’s helpful to u Ref C1A00-54, think that means missing calibration for the suspension Of course not wishing to try and teach I how to suck eggs but auto box should be around 35-40c with the engine running...

Knew I had this somewhere , hope it’s useful to u and it also involves the abs module , not saying that at fault but some comparisons for u...

Forgot to add I’m pretty sure the vehicle dynamics control module is part of the ABS MODULE

Thanks mate yes took me a while but just found it on d3 website vdcm and abs same thing, think its coded, but not sure, only codes I couldn't clear was vdcm, your help with resistance tests confirmed continuity from abs to wheel sensors, and...

Thanks mate changed rear valve this morning compressor ran for a while, then the fickle finger of fate happened, my friend from the local garage turned up needing a 2.7 injector so we did a Norfolk barter, he agreed to come back with his...

Hi mate Indeed u would get a 120 ohms reading with either the instrument panel or abs module unplugged as ur in theory taking on of the 120 resisters away ,, with both of them plugged in it should read 60ohms at the obd2 port If it’s...

Yes thanks mate canbus seems intact will check further, canbus wires are spiraling in the loom?. motor runs sweet, locked in park, still needs 3L transmission fluid, no suspension now has some pressure in bags lifted slightly then compressor cut...

Fitted new speed sensors, bought a new ohm meter, reconnected battery this morning started up runs well on the button, but then it happened dashboard lights up like its Christmas again, big F loads of different codes tried ohm readings from abs...

Bit of a result only one light left on dash and two codes which are temporary, haven't had time to put the wheels on yet, hoping to raise suspension, cycle gears and fill the trans with it's remaining 3 litres, and at least move it remaining...

Bless u and thks for the pics , great bit of work ur doing there mate Other one is in the instrument cluster Hopefully over the next fe days ur be able to pin down the errors Indeed plse let us know how things go , thks

So instrument cluster and abs are the ends of the loop, now I know the pin numbers will test sensor harness for continuity abs plug to sensor at some point and possibly clean the rear hubs too many thanks for your help will keep you posted

Also remember there are different fuses that go to the abs module,, listed above Shame u couldn’t spin the wheels to check the speed sensors as I think u would need to set ur multimeter to Vac to test the voltage as the wheel spins Think...

Thanks mate just what I was looking for your a star will help me get my head round it, already sust that sensor supply and signal go to the abs so can now check continuity, plug to abs will work through issues over next few days, sensors arrived...

Hi mate Ref ur abs module circuit have u done a canbus test plse seeing one of the resisters are inside it Just an idea and great u found the bare wire on the lead With both battery leads disconnected from the battery posts Multimeter set...

Would u also mind sharing what the new abs lead ohms are plse , as would be good to know what they are , many thks

Forgot to add when I had canbus erros of these tests I done, did find it easier using a breakout box Reconnect battery, ign off, meter set to Vdc TP to pin 6 other TP pin 4 Read Vdc ( should be around 2.5 Vdc TP to pin 6 other TP to pin 5...

Sorry ment to say can you reccomend a breakout box something else I would like to learn about many thanks for all you help and advice waiting for sensors today and rear valve block tomorrow many thanks mate

You always help in a big way mate, many thanks. Front sensors read 01.1 on 200m setting, but on 2000 settings reads 489 but the damaged one flashes to 1650 then goes blank?, all readings otherwise the exact same on other three sensors on both...

Hi mate Great that ur making further progress, must confess that rear valve block is indeed awkward to get out, changed all my Voss connections with pushfit which made life a lot easier particularly for that rear one Assume as those 3 x...

Hi mate waiting for new speed sensors before scanning again ap200 is spot on thanks for the heads up, where I'm at, found a bare wire on r/h sensor, ordered new fronts also want to check the ohm reading of a new ones arrive today, rear valve...

Yes abs unit and valve block's only at this point suspected and concentrated on, waiting for a rear vb before removal

Run through all plugs today cleaned with electrical cleaner nothing untoward. Used cleaner on the outside of the plugs to help to free off the little clips. Visibly all looked ok, checked out speed sensors as this could explain at least two of...

Yeah your right couldn't miss this one lol, ordered two new fronts as their out, l also want to check ohm reading of a new one for reference, but do have a gut feeling this is not the only issue but fingers crossed

Sometimes eyes are better than a meter!

Found this r/h speed sensor no ohms bare wire and a join hopefully this is it l/h to check

Quick update be gentle not an auto electrician checked rear speed sensors both read 01.1 on this setting in pic both side exact same am going to clean sensors and all plugs in these areas then move onto front

Hi mate How u getting on my friend plse Hope u don’t mind me mentioning but the 3 x connectors that are normally behind the passenger side wheel arch liner I’m pretty sure after 2007 they were moved to behind the passenger side headlight The 3...