What have you done to your Landie today.

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Picked up a pair of these headlight bulbs everyone has been raving about and fitted them today. Replaced a front indicator that was rotten and had been wired in by a chimp. Adjusted the alternator belt that was so loose it was in danger of falling off. Tried to replace the front mudflaps as one had fallen off completely and the other was about to. Got one fitted without a hitch - but managed to snap off both bolts holding the drivers side one on. Came in for a cup of tea then - couldn't face trying to drill them out in the cold and wet.
 
Last edited:
Tightened up my lightbar on the bumper, stop the pesky lights dropping down, need to sort my bearings as soon as my Socket comes and I get back from Oxford, gotta pick an 'orse up tomorrow hope my bearings stay in good nick
 
Just replaced the headlamp bowls with some new bulbs on the green RRC. Passed its MOT end of August but realised they were not that bright. Could spot some corrosion inside lifting off the reflective surfaces. After getting the rusty bolts off and removing the light guards, taking the grill off, I realised just how bad the bowls were.......one crumbled away to rusty dust!
...new replacements have clear front glass, fancy reflector bowl.....WOW! transformation, the headlights now actually light the road ahead!...result :)
 
joe1972 said:
Just replaced the headlamp bowls with some new bulbs on the green RRC. Passed its MOT end of August but realised they were not that bright. Could spot some corrosion inside lifting off the reflective surfaces. After getting the rusty bolts off and removing the light guards, taking the grill off, I realised just how bad the bowls were.......one crumbled away to rusty dust!
...new replacements have clear front glass, fancy reflector bowl.....WOW! transformation, the headlights now actually light the road ahead!...result :)
Click to expand...

I have a set of clear lensed 'E' marked headlights on order at the moment. As soon as they arrive I can fit both the lights and my uprated bulbs.

I carried some coal from the back of mine over to my house today.
 
finished taking my toys off the old girl, anything i can transplant to the disco anyway, ready to hopefully sell her tomorrow morning.

and thanks to jp i have some room in the garage to store said toys now :D
 
Deflated my tyre and drove over it with a standard Disco to push it off the bead so i could clean all the crap out of it that had caused it to deflate on the greening laning day.
Put some tiger seal round it and pump it back up. No more leaks, lets hope i never get a puncher on it. :lol:

Also discovered blocked sunroof drains and a crap seal on a alpine light were causing my water ingress:
Fixroofleakedited.jpg


Then later fitted 2" lifting blocks to mates Disco. All in all a busy and productive Sunday.

Chris
 
Co-Pang-Yang said:
Deflated my tyre and drove over it with a standard Disco to push it off the bead so i could clean all the crap out of it that had caused it to deflate on the greening laning day.
Put some tiger seal round it and pump it back up. No more leaks, lets hope i never get a puncher on it. :lol:

Also discovered blocked sunroof drains and a crap seal on a alpine light were causing my water ingress:
Fixroofleakedited.jpg


Then later fitted 2" lifting blocks to mates Disco. All in all a busy and productive Sunday.

Chris
Click to expand...

that n/s/b tyre is on ass about face :rolleyes:
 
Set cambelt up and tensioned it on 300tdi, fitted engine back to gearbox and set about fitting engine and gearbox mountings but ran out of time.:cool:
 
Ordered this lot. Got general grabber AT2's and finally went for it.


Safari Snorkel to fit Discovery 300TDI(with ABS)
Diff Guard - Galvanised x2
Full Plus 2 Inch Lift Kit for Disco 1 (with winch - as I intend to get one fitted eventually)
Kit consists of 2 pairs of Britpart Performance Coil Springs (1x DA4202 and 1x DA4204) and 4 Pro Comp ES9000 plus 2 inch Gas Shock Absorbers, 1 pair of front dislocation cones(inc. HD spring retainers), 1 pair of rear dislocation cones, HD front and rear spring retainers, 4x extended polyurethane bump stops, 1x set of Goodridge stainless steel braided brake hoses (plus 4 inch).
Steel Steering Guard - Galvanised - for Range Rover Classic and Discovery 1 RHD and LHD - features j
EGR Blanking Kit - all 300TDI
Britpart Waterproof Seat Covers - Front Pair in Grey
Filter Kit - Disco 300TDI

I have the lilliput 7" touchscreen din radio fitted and currently run it off a laptop. I've recently bought a mini-itx format pc off ebay for way under what I should've got it for and I just need the 12 volt car PSU and then work out where to fit it.
 
Whitey193 said:
Safari Snorkel to fit Discovery 300TDI(with ABS)
Click to expand...

could you do me a favour? when you've fitted the snorkel, could you *please* send me a copy of the fitting instructions???

I have the actual snorkel fitted to my vehicle, but nothing else. No tubes, no clips, no airbox, nothing.

I'd like to look at the fitting instructions to give me an idea for what I could knock up myself...
 
Whitey193 said:
Ordered this lot. Got general grabber AT2's and finally went for it.


Safari Snorkel to fit Discovery 300TDI(with ABS)
Diff Guard - Galvanised x2
Full Plus 2 Inch Lift Kit for Disco 1 (with winch - as I intend to get one fitted eventually)
Kit consists of 2 pairs of Britpart Performance Coil Springs (1x DA4202 and 1x DA4204) and 4 Pro Comp ES9000 plus 2 inch Gas Shock Absorbers, 1 pair of front dislocation cones(inc. HD spring retainers), 1 pair of rear dislocation cones, HD front and rear spring retainers, 4x extended polyurethane bump stops, 1x set of Goodridge stainless steel braided brake hoses (plus 4 inch).
Steel Steering Guard - Galvanised - for Range Rover Classic and Discovery 1 RHD and LHD - features j
EGR Blanking Kit - all 300TDI
Britpart Waterproof Seat Covers - Front Pair in Grey
Filter Kit - Disco 300TDI

I have the lilliput 7" touchscreen din radio fitted and currently run it off a laptop. I've recently bought a mini-itx format pc off ebay for way under what I should've got it for and I just need the 12 volt car PSU and then work out where to fit it.
Click to expand...

Hate to tell ya this, but those Britpart springs will sag in next to no time - even quicker if you have a winch fitted.
Invest in a set of Bearmach HD springs and save yourself the heartache....
 
You must log in or register to reply here.

Similar threads

B
defender 2.4 puma reverse light switch
Replies
4
Views
463
BEASTIE 90
B
Padda.116
300tdi disco 1, new head gasket oil leak!!
Replies
10
Views
551
Padda.116
Padda.116
Knappster
Shot-blasting steel wheels
Replies
9
Views
808
Knappster
Knappster
I
Re-coding of ABS Module after repacement
Replies
10
Views
884
invisible999
I
C
Freelander 1 crank no start
Replies
1
Views
1K
niccage
N
Back
Top