to the tyre treadonly downside was the welding to both outer sills at the rear (have a look on yours
)a mate did it for me so it didn't cost a lot
What have you done to your Freelander today
- Thread starter Freelaner
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
to the tyre treadonly downside was the welding to both outer sills at the rear (have a look on yours
)a mate did it for me so it didn't cost a lot
fishlander
Active Member
- Posts
- 437
- Location
- Taunton Somerset
only downside was the welding to both outer sills at the rear (have a look on yours
a mate did it for me so it didn't cost a lot
Mine has no rust luckily!!,which for a 2001 Y plate is good going.
- Posts
- 83,235
- Location
- Embasinga stocæ
check rear door, particular around number plate. known rust area.
fishlander
Active Member
- Posts
- 437
- Location
- Taunton Somerset
It has a small spot of rust behind the sparewheel where the wiper arm has rubbed it!!!
Nodge68
Well-Known Member
- Posts
- 32,504
- Location
- Near Newquay
No rust on my 2001 V6 except for surface rust on the fuel tank cradle and rear sub frame!!
fishlander
Active Member
- Posts
- 437
- Location
- Taunton Somerset
Their Freelanders so they don't rust,the end!!!!!lol
Bollocks
That's just the door... No photos of the sill unfortunately. Next rust spot will be behind spare wheel and the edge behind the bottom corner of front doors on the 3 door. Mine had a lot of stone chips an rust starting. Rub down, respray and protective plastic now in place
Hippo
Lord Hippo
- Posts
- 52,247
In general Freelanders don't rust. But they will if you cause them damage. Compare yer boot floor to a disco or tratter. Cars rust from the inside out, which is why the manufacturer only gives a warranty for rust through from the inside out. Like the pillar. The rust in the pic looks like the outside edge of the door, which will easily rust if you break the protective coatings. Same goes for the rest of yer Freelander like scratching the sills.
Point taken. The freelander does not disintergrate in a cloud of orange dust like the defenders do BUT they do still rust from normal wear and tear. My door was just a paint bubble when I brought it and it wasn't untill I sanded it back I saw how bad it was. The sills wernt rotten through completely but you can see it is damage from the spray from the roads. Perhaps salt being sprayed upwards. My freelander does not have any offroad damage as the worst it will go across is a wet field or dirty lane. Not enough even for off road tyres. I was also the first person to do this with it as an 'older' couple had it before me and the rust was already there
So my point isn't about where they rust or how they rust. Simpley they do rust occasionally
Last edited:
Nodge68
Well-Known Member
- Posts
- 32,504
- Location
- Near Newquay
Changed engine oil and filter. Took her to the MOT which she passed with flying colours
Fitted the propshafts ready for winter.
Tested the VCU using the torque test, which shows that the VCU has stiffened up slightly even though it's been sat on the bench in my workshop since April? Odd!!
Fitted the propshafts ready for winter.
Tested the VCU using the torque test, which shows that the VCU has stiffened up slightly even though it's been sat on the bench in my workshop since April? Odd!!
mfp2gosling1
New Member
- Posts
- 91
- Location
- Central Scotland
Have you fitted the Synergy box yet Digby?
Spacemonkey...
Well-Known Member
- Posts
- 1,048
- Location
- Darzet
When I was looking for a new Freelander, all were rust free except one and the whole underside was like a Defender- ans worse at the back. The towbar was the clue and I reckon it must have been used for dunking boats in the sea.
Skynet
Well-Known Member
- Posts
- 1,197
- Location
- Melksham, Wiltshire
My FBH hadn't been working for a while.... well since last Feb when the fuse blew so I left it out.
But it wasn't F5.... which is FBH, oil cooler, engine management.... that had blown and that I removed. It was F4, engine management, that I had removed. Replaced the fuse and FBH kicked in as usual. Just so that you guys realise there is a link
Now I just need to replace the thermostat or put a switch in its place.
But it wasn't F5.... which is FBH, oil cooler, engine management.... that had blown and that I removed. It was F4, engine management, that I had removed. Replaced the fuse and FBH kicked in as usual. Just so that you guys realise there is a link
Now I just need to replace the thermostat or put a switch in its place.
my sills aren't scratched or damaged Hippo
they have, however, been subject to long term dampness due to the plastics retaining mud and detritus behind them
Hippo
Lord Hippo
- Posts
- 52,247
You could both put some hammerite under seal with added waxoyl on/under the sills like I did years ago. It dries sort of hard with a wax finish after a bit. Also dinitrol spray cans with the long lance thing for squirting inside the sill from the ends. Not tried it yet though.my sills aren't scratched or damaged Hippo
they have, however, been subject to long term dampness due to the plastics retaining mud and detritus behind them
i shall be thoroughly cleaning the area and liberally applying some thick black underseal to the whole sill area. i will not be refitting the plastic on the underside of the sill
Epicuser
Ex Freelander Owner
- Posts
- 2,393
- Location
- North East Surrey
Collected my lifted, warm TD4 which now stops :lol:
40mm lift kit, new original LR thermostat and had the rear brakes overhauled. They feel soooo much better
40mm lift kit, new original LR thermostat and had the rear brakes overhauled. They feel soooo much better
Last edited:
Similar threads
