200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
Yeah I just finished the air pipes and it runs rough again :/
So when I restrict the airflow it runs a lot better ? What would cause this ?
Trailer - challenge truck build
- Thread starter 200tdi ayre
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Yeah I just finished the air pipes and it runs rough again :/
So when I restrict the airflow it runs a lot better ? What would cause this ?
Mr Noisy
Coming in your ears.
- Posts
- 10,146
- Location
- Altrincham, Cheshire
Not enough fuel!?
Try it with MAF unplugged?
Try it with MAF unplugged?
discomark10
Well-Known Member
- Posts
- 3,977
- Location
- Milton Keynes
Did you check the idle actuator?
discomark10
Well-Known Member
- Posts
- 3,977
- Location
- Milton Keynes
Could even be an air leak
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
What would I check ? It's there and plugged in anyway
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
Just unplugged the MAF and it will run without dying and rev up a lot better, still abit rough but better. Knackered MAF then ?
Mr Noisy
Coming in your ears.
- Posts
- 10,146
- Location
- Altrincham, Cheshire
Quite possibly or needs a tune
Search about on here for MAF adjustment, plenty of info on checking it and adjusting it
You have the CO trim wires that need to be set so the CO output is 1-1.5% and the other wires are the airflow that should rise and fall with airflow, check with multimeter
Get it rigged up to your gas analyser and see how she's burning
Search about on here for MAF adjustment, plenty of info on checking it and adjusting it
You have the CO trim wires that need to be set so the CO output is 1-1.5% and the other wires are the airflow that should rise and fall with airflow, check with multimeter
Get it rigged up to your gas analyser and see how she's burning
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
Quite possibly or needs a tune
Search about on here for MAF adjustment, plenty of info on checking it and adjusting it
You have the CO trim wires that need to be set so the CO output is 1-1.5% and the other wires are the airflow that should rise and fall with airflow, check with multimeter
Get it rigged up to your gas analyser and see how she's burning
Righto I'll have a look around, definately a lot better with the MAF disconnected
Water is finished. Air is finished it runs and just needs tuning
Tidy up the wiring and make the front prop an rebuild the interior and it's done !!!
Mr Noisy
Coming in your ears.
- Posts
- 10,146
- Location
- Altrincham, Cheshire
Famous last words
- Posts
- 8,543
- Location
- Tamworth, staffs.
:hysterically_laughi
Famous last words
Aye, mines be done for 3 years! :lol:
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
Props are made, cowling is made for the electric fan on the rad, just gotta put the temp sensor in line and wire all that up
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
It Drives !!!!
Only off and on the ramp mind but still !!!
Feels like it's going to absolutely fly too
Only off and on the ramp mind but still !!!
Feels like it's going to absolutely fly too
Mr Noisy
Coming in your ears.
- Posts
- 10,146
- Location
- Altrincham, Cheshire
Gonna be belting
Take it the brum brum in a 90 is giving you much pleasure?
Take it the brum brum in a 90 is giving you much pleasure?
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
Gonna be belting
Take it the brum brum in a 90 is giving you much pleasure?
Revving it makes the workshop shake
Love it
jai_landrover
Well-Known Member
- Posts
- 13,392
- Location
- Luton
Nationals 2014 At stAinby quarry Grantham
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
Awesome
Took it for a quick wizz and it's got abit of a misfire at high revs and doesn't seem to be selecting all gears or kicking down, I'll check the oil level tomorrow it may be abit high
200tdi ayre
Well-Known Member
- Posts
- 5,832
- Location
- Ashbourne (sometimes)
Question
What's the maximum allowed offset on a set of wheels for competition ?
I've attained a set of disco steels for nowt from a bloke in the village and so I might aswell have a go making some trialling wheels for it
What's the maximum allowed offset on a set of wheels for competition ?
I've attained a set of disco steels for nowt from a bloke in the village and so I might aswell have a go making some trialling wheels for it
discomark10
Well-Known Member
- Posts
- 3,977
- Location
- Milton Keynes
Question
What's the maximum allowed offset on a set of wheels for competition ?
I've attained a set of disco steels for nowt from a bloke in the village and so I might aswell have a go making some trialling wheels for it
You going to cut n weld em?
jai_landrover
Well-Known Member
- Posts
- 13,392
- Location
- Luton
4 inches measured from the naive plate outter face to outer rim edge
Similar threads
