Freelander 1 td4 no start very hot weather

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
T

toto25

Member
Posts
11
Location
corsica
hi ,
my td4 starts very well when cold, and after driving then stopping the car in very hot weather (+30) the car does not start (starter does not turn).
Do you have any idea of the problem?
I also noticed that the fan in ecm spins when it refuses to start. This fan seems to be controlled by a bwm 35°c temperature sensor located in the ecm box.
Could it be the cause of the breakdown?
do you know where the air is taken that is sucked in by this fan
no error code on suitcase.
pipe air temperature: 44°c

best regards
 
The fan is there to keep the ECM cool. It's not related to or controlled by the ECM, it's completely independent of any electronics altogether.

Have you checked the small trigger terminal on the starter for corrosion? This issue doesn't create a click from the starter.

It's also not uncommon for the starter contacts to burn out. If this is the case, the starter will click, and do nothing else.
 
toto25 said:
thank you for your help, the solenoid is not oxidized and does not click at all.
Click to expand...
Have you checked that you are getting voltage at the small starter terminal when you turn the key to the start position?
Have you checked the start control relay (2) in the fuse box is A working, and getting power when you turn the key?

20220603_151300.png
 
hi , Nodge68
The relay seems to be ok, I measured 100 ohms when hot. And also swapped two relays. But meaning effect. Engine still won't start warm.
thank
 
toto25 said:
I measured 100 ohms when hot. And also swapped two relays. But meaning effect. Engine still won't start warm.
Click to expand...
Have you tried to jump the start relay, to make sure the starter is actually working? (Make sure it's not in gear!)

If the starter is working, then have you checked you're getting the start signal at the relay, when you turn the key to the start position?

If not, have you checked the ignition switch is actually sending out the start signal?

The ignition switch is known to fail sometimes.
 
toto25 said:
no i have not make this test ,
engine cold all is ok
Click to expand...
To me it suggests that something is failing when it's hot. So the starter being bolted to the engine gets hot, so that would be my first thing to check.
Next would be the start circuit from the ignition switch to the relay.
 
Hi, whilst some trys to crank it give the starter motor a tap with a piece of wood (chair leg or similar). As @Nodge68 says it's a good place to start. If it cranks/starts check the battery post cable is tight if it still plays up then remove the starter motor & replace the contacts inside with the kits off eBay.
 
toto25 said:
hi this item ?

Freelander 2.0 TD4 Diesel Denso Démarreur Solénoide Kit Réparation 228000-7801 | eBay
thank you
Click to expand...
Yes that's the kit but first give the starter motor a tap whilst someone is trying to start it, it could just be the post on the starter motor is loose.
When mine had this problem I got the kit then stripped the motor but it only needed the contacts inside cleaning, it's done over 20,000 miles since then & I still have the kit to fit:). The vehicle has about 173,000 miles on it in total & still the original starter motor !
 
You must log in or register to reply here.

Similar threads

E
Freelander TD4 loss of power
Replies
3
Views
1K
Nodge68
Nodge68
Brown
TD5 electronic faults - any ideas?
Replies
15
Views
928
Brown
Brown
Gunter Shingleditch
Freelander 1 TD4 puff of smoke on start-up, stinky exhaust and shudders at 1000 RPM - SOLVED
Replies
15
Views
2K
kernowsvenski
kernowsvenski
kernowsvenski
FL1 TD4 Auto - Transmission whine after cold start - SOLVED
2
Replies
24
Views
956
andyfreelandy
andyfreelandy
T
FL1 TD4 5 Door 2001 CCU
2
Replies
29
Views
2K
TJseries2
T
Back
Top