Series 3 stuff, new and used.

I have decided to sell my Series Landy stuff , I have lots of parts, new and used. PM me if you need anything. Happy to post smaller stuff. Items are near Scottish/English Border on the East Coast. I also have a dismantled S3 (petrol) with a good restored chassis and a complete but knackered S3 (diesel). Also have a S2(a?) bulkhead in need of some restoration but has steering/dials etc fitted. Too good to scrap. Don't be frightened to ask for prices, you may get a pleasant surprise. I may add a list of parts later.

What condition is the diesel exhaust manifold? (And price?)

ben waine said:

What condition is the diesel exhaust manifold? (And price?)

Click to expand...

I should have a couple, I will check tomorrow night and PM you.

how much for the chassis? and does it have a v5

Also after a diesel exhaust manifold and a few other bits if you have!

wondering if series doors would be any good on the 110. parts list could be interesting

got a mig for sale?

In a bit of a hurry right now, going to work, will reply tonight to questions by PM, thanks.

Right, here are some photos of some of the parts. I will make a more comprehensive list. I am kind of pushed for spare time at the mo' so please be patient, thanks.

Where are my photos? I will try again.

Looks like I was trying to upload too many at one time. I will add some more photos.

...and more...

and some more...

Here is a list of some items...1 good radiator, 1 nearly new radiator, 1 nearly new fuel tank,1 new water pump, 2 new rear bench seats plastic covers metal frames by Britpart, 1 front bumper with A bar, 2 bulkhead footwell repair panels (may sell with S2(a?) bulkhead), 2 under wing mud panels, brake pipe set (swb S3), 2 new brake hubs 11" diameter, good pass side door top, used but useable steering swivels, new rear step, used but good heater matrix in cover, plastic rad grilles, 2 front 2 rear new shockers, couple of sets of new springs swb, distributor, 3 new brake hoses, new lift pump, 2 new brake shoes stc3821, 3 new rubber gaitors for h/brake g/sticks, 6 new track rod end clamps incl nuts and bolts, 4 new check straps, 4 safety belts, new gaiter for prop, set new pedal rubbers, new clutch slave cylinder corresponds to 591231G dia 22.2mm, pair new swivel seals, set new wheel nuts, various spring shackles, long and short., crak? seals, used speedo cable, new track rod end with "normal" thread. I have lots more, did I mention a good S3 bulkhead, only needs the mounting brackets repaired.

ben waine said:

What condition is the diesel exhaust manifold? (And price?)

Click to expand...

Still on the engine, I have a S2a diesel engine and a S3 diesel engine, are they the same?

will the rad fit a 2.25 petrol lightweight ?

and how much for the bumper / a bar ?

the egg said:

will the rad fit a 2.25 petrol lightweight ?

and how much for the bumper / a bar ?

Click to expand...

Not sure if the rad is the same. £30 for bumper with A bar. A bar has a slight dent, must be collected from TD145PE.

Can I request any messages are sent via PM to me, thanks guys.

I will add that I have a complete R reg S3 diesel Landrover in poor condition, the chassis is shot and the engine has a strange knock, possibly big ends but I am no expert. I have a complete S2a diesel engine and complete S3 petrol engine. Some gearboxes, axles, not tested. Also a truck cab and two rare cab to body panels, they fit at the rear of the cab and take up the gap. I have a loose rear tub, sides and roof. Numerous front wings and a seat base needing a bit repair to the sides.

These are all advertised elsewhere and a local guy (enthusiast and breaker!) is visiting me on Thursday evening, so.....

The distributor is nearly new, wasn't used much before being removed from engine.