Series 3 Rebuild Series 3 Suffix B gearbox as Suffix D

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Kiwi Landie

Kiwi Landie

Active Member
Posts
116
Location
New Zealand
I have a very tired Series 3 Suffix B gearbox. I sourced it out of a paddock, emptied the water out, cleaned it up and rebuilt it, it works after a fashion, but it really needs a good going over and a lot of new parts.

Can anyone tell me, if I am replacing basically all of the innards, can I rebuild it as a Suffix D?

Or are the cases fundamentally different?

If anyone has done this, a bit of advice would be very helpful. I've found bits and pieces on the web which allude to this being possible, but no definitive statement.

Cheers
Andrew
 
Think so, the suffix A had a different reverse gear, and you've to change all gears to match, if you can get them.

Get the parts manual out and start writing down the parts you need.
 
Wildefalcon said:
Think so, the suffix A had a different reverse gear, and you've to change all gears to match, if you can get them.

Get the parts manual out and start writing down the parts you need.
Click to expand...
I rebuilt mine to suffix D when I did mine, you will probably find most of the parts that need to be replaced to update the box are probably worn already. There are only a couple of parts that you cannot buy genuine.
You may be able to glean some of the parts needed and errors that can be made doing this very thing from here https://www.landyzone.co.uk/land-rover/series-3-109-six-pot-rebuild-thread.367834/page-10
 
Last edited:
Thanks guys. I see from having a brief look on the web that specific Suffix D parts do appear to be in better supply than some of the Suffix B stuff, so it strikes me as the logical way to go, as I'll be doing the lot.
 
The main difference I recon is with the reverse idler and it's shaft, roller bearing not bush. Reversing a series with a bush idler a long way can result in the bush seizing on the shaft! Ask me how I know this.
 
Many of the actual gears are different as well as other internal parts, however if you are doing the lot it makes sense to update.
 
Yep - I'm scouting around trying to find people who have them in stock. The units from TAS in Italy do look to be nicely machined parts, for sure.

Thanks for your help on this.
 
OK - Got the parts rolling in now. The Italian TAS stuff definitely has an air of quality about it, so that's encouraging.

One question - In the parts manual, the reverse selector shaft changes from PN 576729 to PN FRC2053 at September 1979. My suffix D rebuild will be (effectively) 1981 onwards (i.e. after this change point). Does anyone know the actual difference between a 576729 and a FRC2053? I haven't ordered this part and as it is about 150 quid I am reluctant to do so if it is not vital. What did you do Biker B - or did you already have this in your original box?

Cheers
 
Kiwi Landie said:
OK - Got the parts rolling in now. The Italian TAS stuff definitely has an air of quality about it, so that's encouraging.

One question - In the parts manual, the reverse selector shaft changes from PN 576729 to PN FRC2053 at September 1979. My suffix D rebuild will be (effectively) 1981 onwards (i.e. after this change point). Does anyone know the actual difference between a 576729 and a FRC2053? I haven't ordered this part and as it is about 150 quid I am reluctant to do so if it is not vital. What did you do Biker B - or did you already have this in your original box?

Cheers
Click to expand...
I bought my parts all genuine apart from a couple of the italian parts that seemed to made of unobtanium.
I think the reverse shaft came from Malta, there is a place that sells all sort of odd genuine parts that a few bits came from, however they seem to come and go so its just your luck.
I did take about 3-4 month months just tracking all the bits down. Blanchards supplied the majority of them but there were a few outliers.
 
Guess I'll be ordering the reverse selector shaft then!!

I've ordered from about six different suppliers, including the Italians. Blanchard is not on that list but will be after today, as I see that they have genuine selector shafts actually in stock. I found a lot of outfits advertising that they have this and that but when you actually phone and ask, it turns out that they haven't. I'll post a complete list for the benefit of others once everything has arrived and I've successfully assembled it all.

Thanks for that.
 
If Blanchards have a genuine reverse selector then you can bet I bought it from them, they are my go to for bits and I only look at other suppliers if they don't have the parts I am looking for. I did buy one or two bits for the project from Malta but maybe this was not one of them :p
 
You must log in or register to reply here.

Similar threads

D
Series 2a with a Suffix F gearbox. Full Synchro?
Replies
5
Views
832
cornish rattler
cornish rattler
JIMBOB LR
Land Rover Series III Suffix WHAT!?
Replies
2
Views
493
brianp38dse
brianp38dse
W
Series 3 Land Rover series 3 knock
Replies
1
Views
285
steve2286w
steve2286w
Frisol
Series 2a Gearbox Rebuild Issues
Replies
5
Views
902
steve2286w
steve2286w
L
Series 3 petrol trouble shooting
2
Replies
32
Views
1K
lcdck
L
Back
Top