Glenbo
New Member
- Posts
- 74
- Location
- Leicestershire
Disappointing somewhat so what's the easiest way to put one in.
No outside temperature gauge!
- Thread starter Glenbo
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
blue beasty
Leaks an prone to bits dropping off
- Posts
- 61,350
- Location
- Gloucestercotshirewolds
open the window?
I got one from Lidl, It's the same size as the clock in the dash, some folk have even replaced the original clock with these. Cost £4.99. Similar ones to be found on eblag.
I fixed it in the extreme rh corner of the dash infront of the windscreen, works well, but the inside temp reading is way out when the sun shines. Careful positioning of the remote outside sensor is essential for accuracy, mine is tucked in behind the cheese grater gille below the bumper.
I fixed it in the extreme rh corner of the dash infront of the windscreen, works well, but the inside temp reading is way out when the sun shines. Careful positioning of the remote outside sensor is essential for accuracy, mine is tucked in behind the cheese grater gille below the bumper.
Streetlander
Active Member
- Posts
- 227
- Location
- Sydney, Australia
......... why do you NEED one? seems a bit ridiculous!!!!!!
Glenbo
New Member
- Posts
- 74
- Location
- Leicestershire
Personal preference, please don't comment if you don't want to help
2.0_hippo
Well-Known Member
- Posts
- 6,069
- Location
- Hertfordshire
:mooning:
blue beasty
Leaks an prone to bits dropping off
- Posts
- 61,350
- Location
- Gloucestercotshirewolds
your right.....sorry.........the glass bit in the door comes down and then you can reach your hand outside and guage the temperature.
Of course I lucky and don't need to open my window to know exactly how cold it is outside
Streetlander
Active Member
- Posts
- 227
- Location
- Sydney, Australia
.......... wanted to know WHY you NEEDED one so I COULD help
but I spose opening the window a bit too exhausting
All I can say is an outside Temp Guage is about as useful as a flow meter on your windscreen washer bottle!!!!
............. also: Don't post inane subjects if you dont want comments in kind :lvkiss-106:
Last edited:
zoolander
New Member
- Posts
- 375
- Location
- Chatham, Kent
I actually find the flow meter on my washer bottle very useful! Just struggling to work out the pH of the water in the bottle.
Glenbo
New Member
- Posts
- 74
- Location
- Leicestershire
.......... wanted to know WHY you NEEDED one so I COULD help
but I spose opening the window a bit too exhausting
All I can say is an outside Temp Guage is about as useful as a flow meter on your windscreen washer bottle!!!!
............. also: Don't post inane subjects if you dont want comments in kind :lvkiss-106:
Why are you being such a prick? I like to know temperatures as i work with temperatures with work and I didnt say need, I was merely trying to find out if other people have done similar and how
2.0_hippo
Well-Known Member
- Posts
- 6,069
- Location
- Hertfordshire
:welcome2:
blue beasty
Leaks an prone to bits dropping off
- Posts
- 61,350
- Location
- Gloucestercotshirewolds
Dont worry about the temp........your humour guage is stuck but luckily this is an easy fix........place suitable appendige in socket and flick switch
TD4_4x4
Active Member
- Posts
- 283
- Location
- North Yorkshire, UK
A temperature gauge would be useful if you park on the street in winter and you want to predict if it'll freeze overnight. Then you can tell if you need to use a car cover/defroster and allow an extra 10mins or so to scrape the window before work.
Also useful if the temperature drops whilst on a long drive and the road becomes slipper/icey but you can't judge this as you're driving in a nice warm heated cabin.
Why a 20 grand vehicle doesn't have one is anyone's guess, unless it's to save money.
(The MK1 Freelander 'clock' does look suspiciously like something out of a Rover Metro/British Leyland parts bin!).
Also useful if the temperature drops whilst on a long drive and the road becomes slipper/icey but you can't judge this as you're driving in a nice warm heated cabin.
Why a 20 grand vehicle doesn't have one is anyone's guess, unless it's to save money.
(The MK1 Freelander 'clock' does look suspiciously like something out of a Rover Metro/British Leyland parts bin!).
Last edited:
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
you can feel it yourself you dont need a sensor to tell you that
newcyboots
New Member
- Posts
- 240
Glebo,
Take it easy friend - its only alittle bit of banter!! liefes to short!!
Anyhow, everyones different, and if you want a outside temp sensor, then you can easily fit one - although theres no factory fit one from LR.
As riverside says, you can source nice quality units almost anywhere that will fit in the hole in the dash where the existing clock is. I done the same to my freelander using a clock from ebay which had nice big digits, the inside temp display, and the outside too.
I instlled the clock in the hole, ran the sensor wiredown behind dash, out by bonnet release cord, then tucked it low down inside the inner skin of the rear wing.. you couldnt see a single wire, it looked mind. The clock and temp were powered by batteries, and it was illuminated at night via a 12v car adaptor - as i thought that would look a bit odd, i wired the clock directly into the 4 pin connector that used to power the old clock (LGW wire to + and black to - on clock.
Theres a pic of how it looks on one of my old threads on here about 2 months ago titled 12v power from clock?
Ive got to be honest, as good as it looked, you could tell that it wasnt supposed to be in the hole where the original was.. So i reverted back to the original....
Good luck whatever you choose to do... And enjoy the banter, dont take it so serious.. In the few months ive been on here, ive seen theres some seriously clued up people on here that can save you a fortune, and give top advice.. A bit of banter back, and youll be fine
Take it easy friend - its only alittle bit of banter!! liefes to short!!
Anyhow, everyones different, and if you want a outside temp sensor, then you can easily fit one - although theres no factory fit one from LR.
As riverside says, you can source nice quality units almost anywhere that will fit in the hole in the dash where the existing clock is. I done the same to my freelander using a clock from ebay which had nice big digits, the inside temp display, and the outside too.
I instlled the clock in the hole, ran the sensor wiredown behind dash, out by bonnet release cord, then tucked it low down inside the inner skin of the rear wing.. you couldnt see a single wire, it looked mind. The clock and temp were powered by batteries, and it was illuminated at night via a 12v car adaptor - as i thought that would look a bit odd, i wired the clock directly into the 4 pin connector that used to power the old clock (LGW wire to + and black to - on clock.
Theres a pic of how it looks on one of my old threads on here about 2 months ago titled 12v power from clock?
Ive got to be honest, as good as it looked, you could tell that it wasnt supposed to be in the hole where the original was.. So i reverted back to the original....
Good luck whatever you choose to do... And enjoy the banter, dont take it so serious.. In the few months ive been on here, ive seen theres some seriously clued up people on here that can save you a fortune, and give top advice.. A bit of banter back, and youll be fine
Glenbo
New Member
- Posts
- 74
- Location
- Leicestershire
Most of my previous vehicles have had them and i agree about the clock, I found it very useful on the last cold spell when doing breakdowns at work when it was -19 and oil was starting to freeze to heaters i went to
OldIrishWulf
Well-Known Member
- Posts
- 3,974
- Location
- Great green Hibernia .
drill a hole through the roof and stick one of these through to the outside air
perfek.
Glenbo
New Member
- Posts
- 74
- Location
- Leicestershire
drill a hole through the roof and stick one of these through to the outside air
perfek.
Lol bee sting thermometer
nsgdm1
New Member
- Posts
- 26
- Location
- sunny nunny (warwickshire)
Surely no need to drill a hole Just poke it through the rust on the sunroof framedrill a hole through the roof and stick one of these through to the outside air
perfek.
Mantamad
New Member
- Posts
- 1,067
- Location
- Fife Scotland
