Front diff bearing tool?

With a suitable bit of steel tube will the front diff outout bearing hammer onto the shaft or is it a press job
Dev

inner or outer?

Its the outer,cheers

outer just slips on once the diff is back in its case then the spacer washer goes on and then the flange followed by another washer and then the nut as far as i remember.

HTH

im not having a good day here,will try again in a bit

I think we are at cross puposes here, I am talking about the front propshaft out put shaft bearing, as in front shaft off, drive flange off, circlip out, shaft & bearing out, no puller so outer race and bearing off with and with a bfh cracking the outer race , inner race off with a slitting disc, So will the new bearing chap on with said bfh or is it a trip to the man with a presshope you can help cheers
Devlin

Devlin said:

I think we are at cross puposes here, I am talking about the front propshaft out put shaft bearing, as in front shaft off, drive flange off, circlip out, shaft & bearing out, no puller so outer race and bearing off with and with a bfh cracking the outer race , inner race off with a slitting disc, So will the new bearing chap on with said bfh or is it a trip to the man with a presshope you can help cheers
Devlin

Click to expand...

are we talking diff or tranny end? if its the diff then its prop off, flange off outer bearing will fall out once the diff is pulled from the case tw@t the race out from inside the diff and drive new race in using old one slit with disc diff back into case slip over new bearing washers et al, if tranny then the same but the bearing is not a taper bearing and needs to be removed after you have taken out the big circlip in the tranny case, hang fire i will try and get the image up so we are talking about the same thing, wanna go to pm?

Sorry yes its the transfer box end, yep Pm me with what ever you think may help
D

Allbrit.de - Ersatzteile für LAND ROVER & MG ROVER

are we talking about number 8?

Devlin said:

Sorry yes its the transfer box end, yep Pm me with what ever you think may help
D

Click to expand...

why you calling it the diff then? :doh:

its not a taper and is a fecker to get out

Whats number 8 , Yeah should said centre diff or trans box early start need a kip or beer

Allbrit.de - Ersatzteile für LAND ROVER & MG ROVER

number 10?

Thats the one, 10 it is,
Cheers

reet then its a doable job but you will need some decent picks or small hooked type things to get the old roller bearing out, dont forget the circlip as that really stops it all moving about and it really really wont come out with that still in-place, dont ask me how i know
and try and get a new felt washer to stop any oil leaking through the shaft and fit a new oil seal too.


good luck.

bearing is stc1130 and if you remove flange seal and circlip ,then replace flange with nut you can lever bearing and shaft out together , then swap bearing and tap both back in preferably with copper or other soft face hammer

jamesmartin said:

bearing is stc1130 and if you remove flange seal and circlip ,then replace flange with nut you can lever bearing and shaft out together , then swap bearing and tap both back in preferably with copper or other soft face hammer

Click to expand...

bugger, you know i didnt think of that:doh: why didnt i just ask you james???????????

DiscoPol said:

bugger, you know i didnt think of that:doh: why didnt i just ask you james???????????

Click to expand...

have you been away for a bit ?

jamesmartin said:

have you been away for a bit ?

Click to expand...

just a bit busy working im afraid James but schools out for summer, as they say, so i have a bit more time to get on here and get some stuff done on the disco before i flog it.

So I take it the bearing will come off the shaft easily enough, but putting the new one on ?????,
D

Devlin said:

So I take it the bearing will come off the shaft easily enough, but putting the new one on ?????,
D

Click to expand...

yes will just tap off and on ,never use steel to hit a bearing though soft face hammer only