Found this in my defender.. not sure what it is.
- Thread starter fumiyasu
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Turboman
Mab An Gov
- Posts
- 60,151
- Location
- Lathrowda, Kernow
Base of the jack.
top drive
Well-Known Member
- Posts
- 2,694
- Location
- Peoples republic of culter
Thats the foot plate for e screw jack
top drive
Well-Known Member
- Posts
- 2,694
- Location
- Peoples republic of culter
On van back/pick ups it attaches to the rear bulkhead behind the front seats .
Turboman
Mab An Gov
- Posts
- 60,151
- Location
- Lathrowda, Kernow
Don't know what motor you have got, but on the front of the bulkhead behind the front seats on mine there are some little brackets with rubber bands that hold the tool roll and jack.
bluedog333
Well-Known Member
- Posts
- 5,357
- Location
- Henley on Thames, Oxfordshire
Only of use if you actually carry the jack in the Landy too, surprising how many people don't!
bluedog333
Well-Known Member
- Posts
- 5,357
- Location
- Henley on Thames, Oxfordshire
Z
top drive
Well-Known Member
- Posts
- 2,694
- Location
- Peoples republic of culter
And the jacks only any good if your front and rear jacking tubes havnt rotted ..... Most have 
Turboman
Mab An Gov
- Posts
- 60,151
- Location
- Lathrowda, Kernow
And the jacks only any good if your front and rear jacking tubes havnt rotted ..... Most have
4 foot Hi-Lift fits behind the seats too.
ReadySalted
Active Member
- Posts
- 444
Yeh I've never been sure where to keep it. It just tends to float around the landy either in the 2nd row footwell or the boot. Normally making a racket pinballing off from one side of the tub to the other as I drive along.
I carry the factory jack but don't even know where the jacking points are. I have a bottle jack out of a disco with me in any case.
I carry the factory jack but don't even know where the jacking points are. I have a bottle jack out of a disco with me in any case.
Turboman
Mab An Gov
- Posts
- 60,151
- Location
- Lathrowda, Kernow
As I said earlier, ther should be rubber bands t secure the jack and tool roll.
Front jacking points are on the ends of the chassis rails under the bumper, they should have rubber plugs in when not in use. Rear are two holes in the rear crossmember.
top drive
Well-Known Member
- Posts
- 2,694
- Location
- Peoples republic of culter
Factory jacking points are the 2.5cm diameter tubes in the rear xmember and if you pull the rubber bungs out of the front of the chassis rails there are tubes there too....
But as i said , many of the tubes are rotten.
But as i said , many of the tubes are rotten.
top drive
Well-Known Member
- Posts
- 2,694
- Location
- Peoples republic of culter
Good to know a 4 ft fits as thats where mines will be living in the cab once its rebuilt. Those screw jacks take forever and i wouldnt thank anyone for one
Turboman
Mab An Gov
- Posts
- 60,151
- Location
- Lathrowda, Kernow
top drive
Well-Known Member
- Posts
- 2,694
- Location
- Peoples republic of culter
Never used mine tried it in the garden and thought poke that., used to carry a trolley jack in the van back , but i got a truck cab now.
Like you say unstable and my rear cross member was rotten i didnt dare risk it.
Like you say unstable and my rear cross member was rotten i didnt dare risk it.
bluedog333
Well-Known Member
- Posts
- 5,357
- Location
- Henley on Thames, Oxfordshire
Get a bottle jack. I carry a farm jack and a bottle and in normal circumstances I'll always use the bottle!
bluedog333
Well-Known Member
- Posts
- 5,357
- Location
- Henley on Thames, Oxfordshire
Lighter, easier, quicker, can be used on other cars... Just make sure you get one with an axle cradle (Disco,RR, older Landies, Mercedes Sprinter etc.).
Similar threads
