Search results

Issues 1 to 69 of Classic Land Rover magazine. Issues 1 - 60 (i.e years 1 - 5) bound in CLR magazine folders. The remaining 9 magazines are loose. All well thumbed but perfectly readable. It be a shame to bin such a helpful resource so some have 'em. Free to collect (Mid Sussex, RH17) or can...

SOLD Marine Blue and Limestone hard-top Original 2.25, 5 main bearing petrol engine, fully-syncro gearbox, transfer box and axles. Documented 84,000 miles and MOT until March 2021. Significant overhaul completed in Spring 2018 (documented...

All gone now, thank you.

Looking at this month's CLR, there is a report that an out of phase prop shaft can cause an grinding noise on the over-run, a problem I'm facing. Can anyone shed any light in this? I can understand constant vibration due to poor prop phasing but I can't get my head around a grind on over-run. I...

On the one day it's rained in the last 2 months I found out how much my roof leaks. Oddly, it's not the rubber seals between the panels but the guttering round the top roof panel. The water fills up the channels on the inside. Looking down the external gutters someone has put some sort of...

Purchase or borrow of a higher ratio diff to test in my S3 before looking further at an High Ratio transfer box conversation. Located in Sussex but prepared to travel for the right thing. Edit: should add, needs to be 10 spline. Cheers

Hi folks. I've need to find TDC on #1 to fit an electronic distributor tomorrow. The destructions say something about setting the engine as above. What's the easiest method? It's not like I'm setting the tappets so is getting the rotor are pointing at lead 1 sufficient? Any guidance/advice...

Previously fitted to my Series 3 but never used, the reality is I probably never will so it would be better off with someone else. GLR101 Fairey capstan short bollard winch, together with the brackets etc to operate it; also comes with the stubby cranking handle so it can be operated manually...

I'm trying to read the searial number off my block for insurance purposes, I know where it is and how many digits it should be from Glencoyne's very helpful website http://www.glencoyne.co.uk/engno.htm; what I dont know is whether the final digit is meant to be a letter or a number, mines not...

Having run Harry round for a few miles now it's clear there is a strong rumble coming from under the driver area on part throttle. No rumble on no-throttle or above 50% throttle upward. There is also a terrible rumble using 4wd. I'm fairly confident of a transfer box front output bearing on the...

Does anyone have a decent picture of Rayleigh trimmed seats in their tratter? I'm refurbing a set of Defender seats for my Series and no one does the covers I actually want (Neptune) as the material is out of stock, so I'm looking at others; Denim Twill, Moorland or maybe Rayleigh, if I can get...

So, MOT failed.... Both side lights inoperable. Strange, they worked when I left for the MOT station about 4 miles away. Get home, the rears don't work now either. All 4 side lights out.... can't be 4 bulbs gone, shirley? Check all the wiring / switch - fine. Have a look in one of the front...

Part Number RTC 3627 Brand New in Box, part of a job lot of bits but no good for my Series. Genuine Land Rover (Lucas) brake cylinder, never been fitted. Please check part number for correct application. £15 delivered.

On rebuilding my SIII I've run into wiper issues. The arms should travel in opposite directions (divers side anti clockwise, passenger clockwise) but mine both go clockwise. They do however park in the right place. I think this means I need to invert the wheel box on drivers side but before I...

SOLD One 1/4 inch (MR5K) and one 3/8 inch (XR8K) Mac Tools ratchet, made in the US of A. Brand new and never been used, I managed to blag these under warranty (paperwork to prove if necessary). I had the originals for years and used them professionally and at home. These come with a lifetime...

I'm trying to upload a FWH manual to the forum for general assistance but there doesn't seem to be a way to do it. I've used the Search but can only find references to people asking to be emailed which defeats the point. Is this something that could be added if not already available? Thanks

New & never been fitted. Driver & Passenger side mud shields for Series 3 Land Rovers, will possibly fit earlier Series too. Part numbers MRC6081, MRC 6082 and 330459 (fits RHD vehicles). These are aftermarket products purchased in a job lot of bits which are surplus to requirement. These...

I think my Starter might be shot, I tried bench testing the the engine by short circuiting the loom and just running leads from the Battery to Starter leads with jump leads (2 for the Earths!), and the Coil + to Distributor. I didn't even get as far as seeing if it would run as the engine would...

Morning gang. Is it ok to use 75w80 MTF in the gearboxes and axles instead of GL4 EP90? I'm struggling to get hold of GL4 and ECP have a deal on this at the moment...

I've ordered a refurb kit for the Series 3, and its come in a little blue bag.... The steering box is on the bench and its not like I need to get the vehicle back on the road pronto. Is it worth rebuilding using this kit, or am I shooting myself in the foot? Any experience of Brit Part or any...