Search results

Hi I’m trying to remove the rear connector off my old radio cassette it came off a defender but early freelander same too, the black outer slides up but retained by 4 lugs on the radio as shown on replacement ( thanks Isobel) but seems solid Any ideas next step @andyfreelandy @isobelwright13

post from Chris 83500 in the engine section who has disco probs any ideas Hello, Hello I'm in the garage The 4x4 is put in mountain mode by itself how to remove this mode Because the mountain light lights up and it is impossible to remove it and the light with the red triangle. The...

Series diesel pistons for sale good condition used , Genuine Rover

I bought this book ages ago , it’s full of select articles from LRO magazines over the years and a go to for lots info, I git curious about the 88 KYJ 57P that was bought and then restored in articles in the mag. wondering if it was still on the road mot check comes back and it’s mot’ed till...

Replacing the ring gear on my 5mb diesel flywheel, old one off easy enough having a mare getting new one on, next try I’m now heating it above the recommended 250C to 260C and cooling flywheel in freezer but not sure if the cold flywheel more of a hindrance as it might cool the ring gear tooo...

https://www.ebay.co.uk/itm/Land-Rover-Discovery-1-200-tdi-radiator-frame-/224793507675?mkcid=16&mkevt=1&_trksid=p2349624.m2548.l6249&mkrid=710-127635-2958-0...

Can someone please confirm if there is a steel lid to fit the air filter housing or does the filter element seal on the bevelled top diameter and clamp on with plastic wing nut Thanks

Discovery 1 200 tdi rad , tested a couple of years ago while testing the engine Will be selling on eBay not sure if to break it down first let me know if interested looking for £60+ postage to get rid Airbox on eBay now

Clearing a few bits out of garage left over from my 200di into series 3 conversion now on eBay Power steering pump NOW SOLD Power steering pump bracket SOLD 200 tdi engine mountings I also have a decent rad / intercooler and turbo and manifold which may put on next week...

Just trying to fill up at Tesco’s earlier and pulled the trigger and it dropped a litre or two on the floor underneath tank , oh dear disapproving looks all round mid fuel shortage! On inspection the filler hose 543764 is split just as it goes through bulkhead It was a really awkward, kinky...

I pulled out the rear axle the other day for a full refurb and paint job Derusted in a wheelie bin and acid bath for smaller bits The axle had a couple of filled area on the diff pan, the welds should have come a bit further out as it’s thin at edge of weld I also found some filler towards hub...

just come across these vids, very cool indeed

:oops:

As always happens change wheel cylinders one side next month otherside goes , the LH cylinders I cleaned up and installed new Girling seals I had in garage as an experiment, looking for a reasonable wheel cylinder hone now, it was now pulling to left due to drivers side shoes all soaked in brake...

The MOT is due in a weeks time and just checking lights over, swapped 2 front side lights and noticed the front bumper mounted Lucas spot sealed beam unit has gone on near side I’ve removed it but was wondering if I left the drivers fog light on would MOT man be Ok with this or do they need to...

I tried today to get the tyre or even one side of tyre off rim to install another tube It’s deflated off , away from the inner bead but so stiff a 2’ crow bar won’t touch it Has anyone changed one by hand before with levers Can a tube be inserted without getting one side off wheel I’ve seen u...

Allegedly Easy to spot Usually have odd starting prices and want direct comms outside of ebay I wonder how many got caught out . Not just landies

Got my new speedo cable, genuine for less than £30 to replace the old worn one! Should these be oiled , greased or left as is before fitting I’ll secure it properly this timeo_O

It’s been a bit smoky, low on power, and checked the compression today it’s about 95 on cylinder 3 and about 270 on the others , I know it sounds low but it starts well Disappointing as I’ve just got it back together I’m not sure if it’s gasket or rings the exhaust pipe is wet and black There...

After 5 years of the 200tdi engine sitting in the garage I finally got round to stripping it down checking for wear and putting new bearings in. this is described on another thread here https://www.landyzone.co.uk/land-rover/200-tdi-engine-checking-refurb.346897/ Must haves on this project for...