Search results

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
  1. DiscoNickY

    auf_wiedersehen_pet's build thread.

    Is it Kawasaki green that mate? Going to pick a 90 up and start a rebuild an was thinkin of going for the same green u used.
  2. DiscoNickY

    Discovering the Discovery... Basic Rebuild...

    So u can cut sill away without touching the floor? Did u make new body mounts/outriggers? Bet ur missus is made up with the mess uve made of that path! Haha
  3. DiscoNickY

    Discovering the Discovery... Basic Rebuild...

    Need to do to OSR arch myself and sill... Very soon!! Any other pics of progression of the job?
  4. DiscoNickY

    Some pics of my Disco :D

    No mate. 24. Late 200. Bit of a mungrel. Mish mash of 200 and 300 bits.
  5. DiscoNickY

    Some pics of my Disco :D

    Never been Bala before. Not much deep water is there. I've had my fill of ridiculously deep water now anyway. Think I'll steer clear of it. Haha. Sure there'll still be more breakages tho.
  6. DiscoNickY

    Some pics of my Disco :D

    Brilliant. Cheers fellas. Off to Bala p&p this weekend so need to get It sorted ASAP.
  7. DiscoNickY

    Some pics of my Disco :D

    Cheers mate. So how do I access this wiper motor? Engine bay or in car?
  8. DiscoNickY

    Some pics of my Disco :D

    Nightmare of a place. Won't be goin again. Another problem that has arose is the rating the temperature adjuster had just gone slack and it's stuck on cold!?!?
  9. DiscoNickY

    Some pics of my Disco :D

    Could it be a flooded relay that's packed in? Anybody know which relay is for wipers?
  10. DiscoNickY

    Some pics of my Disco :D

    Electrical problem now mate. Went through rather deep water at hill and ditch on weekend. Now the wipers will not stop!!!!! Help please.
  11. DiscoNickY

    Some pics of my Disco :D

    That's all I'm after the stubby. Ill use original front section in stainless and make a little middle section up with a cherry bomb in with tht stubby on end. That's the plan anyway.
  12. DiscoNickY

    Some pics of my Disco :D

    Where did u get exhaust from mate?
  13. DiscoNickY

    auf_wiedersehen_pet's build thread.

    It's so dirty.....?!
  14. DiscoNickY

    Some pics of my Disco :D

    Ok. Cheers guys. It's got 2" on springs an 2" spacers. Was just thinking of replacing spacers with 1" because to be honey the spring doesn't sit completely flat in seat the front is raised which would mean the axel still isn't sitting flat even with 6 degree castors so an inch drop might sit better.
  15. DiscoNickY

    Some pics of my Disco :D

    Ello noisy. Quick question to run by u mate. I've got a 4" lift on mine with the 6degree cranked arms but the high lift is putting too much strain on uj's an output shaft bearings etc so I wanted to drop it an inch or two but obviously don't want to fork out for the 3degree cranked arms. Would...
  16. DiscoNickY

    Some pics of my Disco :D

    Think it woke everybody up. Jesus that's loud. How long till the plod pull u over for that I wonder?!?!
  17. DiscoNickY

    chris's disco thread

    I'm only 26 myself. Lost count of the bikes I've blown up and smashed up pushing them that hard. Ride it like u stole it!!! Haha
  18. DiscoNickY

    chris's disco thread

    No point doing a track day unless ur on the edge of death!!!
  19. DiscoNickY

    chris's disco thread

    Only 2 kinds of riders mate, ones that have been down and ones that are going down! Remember that!!!! Rear arches are easy enough. If u want to do a proper job means taking rear quarter panel off but can be done without removing it.
  20. DiscoNickY

    chris's disco thread

    Track time??? Bye bye 636!! haha I wrote off a gsxr on a track day. Thought I was Valentino rossi, apparently not. Ha. My arches went in same place bud and around seat belt anchor. I've done one an will be doing other soon.
Back
Top