Search results

Hi all. Can I use a 12 volt Ignition Switch on my 24 volt FFR109. It does not have a steering lock. Regards. Chris.

Hi All. The inficators have failed on my 1984 FFR 109. The Hazzard and all other lights are working. Is the problem likely to just be the Stalk.

Hi All. I am contemplating putting a 24 volt Fuel Pump on my 1984 109 FFR Petrol. I am having problems with the mechanical pump. It keeps draining back into the tanks. Would you recommend any perticular make or type and has anyone done this already. Regards. Chris.

Hi all. Anyone aware af engine recalls on Discovery 4. My son in laws engine has packed in. It is 2012. Regards Chris.

Hi all. I have a 1984 109 FFR 24v. The Fuel and Temp guages are both faulty. I searched the Forums for this issue and it appears that the Voltage Stabeliser is faulty. The wiring diagrams show this, however I cannot find one on my dash as indicated. Is it located somewhere else or is there some...

Hi all. Is it possible to tow start a 2001 Freelander 1 Automatic. Regards. Chris.

Steering. Hi all. Would putting extra weight in the rear of my 1984 Series 3 FFR lighten the steering any. Regards. Chris.

Hi all. is it a good idea to pump expanding foam into the Chassis of a 1984 Series 3 ?. Regards. Chris.

Hi. Are the Starter Brushes interchangeable on a 12 volt and 24 volt system. Regards. Chris.

Hi All. Can I use 12 v Ign Points and Condenser in a 24 v FFR Ignition System.Also, are the 12 volt Starter Brushes compatible with the 24 volt Starter Brushes. Regards. Chris.

Hi all. Would anyone know what is the difference in length of the rear shackles on a Series 3 LWB and a SWB. Also, will the SWB Shackles suit a LWB. Regards. Chris.

Hi All. I have just purchased a new Wolf 130 Mig Welder. Could anyone recommend the setting I should use to weld on sections of 2mm Steel. I have tried various settings already, however, none seem to be very good. Also, one uTube video suggesting welding without the Shroud covering the Tip. Is...

Hi All. I want to strip the Chassis back to bare metal. I have tried Nitromorse and it is useless. I have started sanding, however it is very slow and difficult to get at some areas. Some web sites suggest using Brake Fluid. What are your thoughts on this or any other suggestions. Regards. Chris.

Hi All. Could anyone please help me with the Part Number for the Universal Joint on the Rear Prop Shaft, (next to the Rear Diff Unit), on a 1984, 109 ,2.3 cc, Petrol, FFR. Cant find it in the Parts Manual. Regards. Chris.

Is Zinc 182 Grey Rust Primer any good. I have removed all the loose paint and rust with scrapers, wire brush and finally with paint strippers. There is still about 70% paint still on the Chassis. Regards. Chris.

Hi. I am restoring my 1984 109 and need to remove an LPG Tank from the Tub. The Tank is about 25% full. Is there any way to shut off the gas at the Tank or do I need to drain off all the gas when I disconnect the pipe feeding the Vaporiser ?. It is a Romano Stage 1 LPG Kit. Regards. Chris.

Hi. What size Bolts secure the wings to the bulkhead on a 1884 Series 3 FFR. Thanks. Chris.

Hi. The full length hood on my 109 FFR is torn at a few places along the seams which I was going to try and re-stitch, however, my main problem is that the canvas is no longer very pliable, in fact it is more like leather. Is it possible to soften the canvas prior to stitching. Regards. Chris.

Hi. I have a 1984 109 FFR and I want to try and lower the rear about 2". I have replaced the Extended Shackles with Std ones, but is still too high. Looking closely at it, I was thinking that if I moved the Shackles from the rear of the springs to the front of them it might do the trick. Is this...

Hi All. The heater on my 2001 Freelander 1 Diesel is not working. The Fan is fine and the Temp Guage goes about half way up. Where should I start looking for the problem. Regards. Chris.