Search results

Hi all. Well, after 6 years of owning my 4.6 P38 I have let her go, not far mind, my Son is now it's new owner. Despite the tails of woe that abound I found my P38 to be a reliable, dependable machine. It has been well maintained and well looked after and has never let me down or left me...

Hi all, Got my 4.6 V8 P38 out of storage at the beginning of November and returned it to the road for Winter. All good until yesterday, driving along when suddenly the radio went off, the speedo and rev counter stopped working, dash came up Gearbox Fault, Traction Fault etc but, fortunately the...

DIY Bond car Pt. 2 - Ejector seat - Top Gear at the Movies - Top Gear - YouTube :):)

Hi all. I was looking through the How to section and saw the thread on Diesel re-synch using the Nanocom Evo. As in this thread title, I have the Motronic V8 modules in my Nanocom and wondered if the procedure to re-synch is the same ? If not, could one of you clever gents guide me through...

Apologies if this has been posted before. All that work for £1000 profit, these Guy's do make me smile :) http://www.carvideos.eu/wheeler-deale... Wheeler Dealers Season 10, Episode 3, Joyas sobre ruedas, Experto en carros. In Discovery Channel in English. I do not own any of the...

FAI WATER PUMP RC892671P TO FIT LAND ROVER RANGE ROVER 2.5 91-94 OE QUALITY | eBay WTF........

Hi all. Discovered small splits in lower ball joint covers so I will be replacing all 4 ball joints. Got the tools for pressing the joints in and out, alignment will be down to measurements, wondered if anyone can advise on what joints to get ?. I usually use Island 4x4 for parts and they...

Good day to you all. At the end of March the P38 was laid up for the Spring / Summer season and the MG ZT put into service. Before the lay up I had two minor problems which although annoying, didn't prevent me from using it. 1. Sometimes the engine was reluctant to rev over 3000 rpm and...

Perhaps a fire Extinguisher may have save it ? :eek: Range Rover Burns On Trail - YouTube

Hi all, Not posted for a while as the P38 has been in mothballs over the spring/summer period but, now autumn is with us it's being put back on the road, and it's the turn of the MG to be laid up until next spring. To the question as in the title. I have the SRS warning light on and the...

Hi all, over from the RR forum for some advice. My mate has bought a 2000 Freelander which we collected yesterday and it drives quite nicely. We have discovered that the rear tailgate does not unlock and open either with the central locking or using the key, nothing appears to happen, no...

Hi all, About to remove and reseal the valve block on my 1999 4.6 HSE as it is loosing all it's air when left for a couple of days. While i'm at it, I want to fit an inline pressure gauge. Can anyone tell me where the pipe from the valve block to the tank is located on the valve block, don't...

Hi all, Fitted a couple of self adhesive metal hooks to the back of my Nanocom Evo so I can observe live readings on the move. They are the easy remove type which leaves no mess from Asda.

Hi all, Hopefully someone can help me on this. I have had my P38 4.6 HSE (Thor) for 14 months now and have had no problems with the EAS whatsoever. A few weeks ago I purchased a Nanocom Evolution II which is a brilliant bit of kit, and while looking for fault codes the EAS came up with...

Hi all, Over the last 12 months this forum has been invaluable for it's information and general willingness of it's members so, I would like to give a bit back if I can. I purchased a Nanocom a couple of weeks back for my 1999 4.6 HSE Motronic (Thor) and have had time to play and get to...

Following on from my other post "Interior Tart Up" the panels are all back in place and I am pleased with the results. Not to everyone's taste I know, but better than the scratched cheap looking original plastic finish I think.

Hi all, Yesterday was a good day all in all. Heater core o rings replaced and dash reassembled, all fine and dandy. This morning, SRS Airbag fault showing so connected Nanocom to find "Drivers Airbag open circuit" (current). So, maybe a bad connection but I only disconnected SRS loom...

Hi all, Connected new Nanocom to my 1999 4.6 HSE to see why book symbol is illuminated on HEVAC screen. Nanocom showing the following fault :- L/H Blower motor stop mode fault ( Current ). I take it this means the L/H blower is knackered, can anyone confirm please.

Evening all, Received my Nanocom Evolution II today and have been having a bit of a play. All it came with was a single A5 sheet "Quick Setup Guide V 1.1". Went onto Nanocom Website, obtained unlock codes and entered into device ok. Have looked at the on line User Guide which tells you the...

Hi all, Can someone identify the colour of my interior please. I have seen some leather centre console side panels for sale, described as Tan, but not sure if they are the same colour. difficult with photo's I know. Tried from VIN but it comes back as Ash Grey so, interior has been changed at...