Search results

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
  1. L

    SERIES 3 Heater blower question.

    Hi all. Hope you are all keeping well in these most difficult times.....I have a question about my heater blower unit. With the 2 stage switch, it blows from very slowly to slowly. I'm sure it's working as designed but it's pathetic compared to the blast from my other halves Renault Megane...
  2. L

    Range Rover Classic coil springs.

    Hi all....Do any of you know the part number/colour codes for the standard OE coil springs? I want to keep the softer ride. Thanks all....
  3. L

    REMOVING BUMP STRIPS

    Hi all....Just wondering how easy or difficult it is to remove the bump strips on my E reg classic. I am in the process of rubbing down for paint and the bump strips are in the way for flatting the curved edge pressings behind them. One of the strips is bending away from the panel on one end and...
  4. L

    Range rover classic coil springs

    Hi all. Hope you are all keeping well. Just a quick question on the Britpart coil springs. I want to freshen up my tired rusted springs and was wondering if any of you tried the Britpart black springs. I don't want the much too hard yellow ones as I want a softer ride. The black ones appear to...
  5. L

    Range Rover Classic bottom tailgate rust repair?

    Hi all. Hope you, and all who are dear to you are keeping safe and well during these difficult times....I was just wondering if seeing as it's nigh on impossible to find a decent second hand bottom tailgate, and I am up to having a go, what with all this spare time on my hands, have any of you...
  6. L

    Wiper spindles rotten

    Hi all. Hope you are all healthy and coping well through these difficult times.....I have a quick question. My suffix B Range Rover which I am currently trying to bring up to roadworthy condition had been lying up outside for 8 years in the elements and while it survived quite well considering...
  7. L

    Range rover classic new springs

    Hi all. I think the time has come to renew the springs, shocks and bushes on my F-plate classic fitted with the Mazda SLT3500 and I'm not too sure which springs and which load rating I need because of the heavier Mazda lump. I would like to lift it by 1 inch to allow for some slightly larger...
  8. L

    Hazards question.

    Hi all, and a big happy new year to each and every one of you. Hope you all are enjoying the festivities.....I have a quick question regarding the hazards on my series 3. Does the small bulb inside the warning pull switch complete the circuit for operation. Mine have stopped working and the only...
  9. L

    Series 3 gearbox speedo drive removal

    Hi all. Hope you are all enjoying the festivities. Just a quick one. I went to change my speedo cable today and sure enough, the cable had snapped off in the drive unit and the remains are seized into it with no spur to grab onto with a pliers. My question is, can the drive unit be removed to...
  10. L

    Series 3 brake servo repair

    Hi all. Just a quick one. Are the brake servo's on series Land landy's serviceable.....i.e. can they be opened up and the seals and diaphragm be changed. John Craddocks are listing a repair kit but I just want to be sure?..... Thanks all.
  11. L

    Range rover Classic roller/Brush painting

    As above.....Anyone tried it with good results. I have a daily hack that is looking a bit rough and needs something done with peeled lacquer and faded spots in the paintwork. It will never be a show car and I use it for what it was meant to be used for. Working hard it's just looking a bit jaded...
  12. L

    P38 Diesel power issue

    Hi all. Was just wondering if there is any way to squeeze a bit more performance out of the M51 without fitting a power box or chipping the ECU. A friend has an Auto and is convinced she heard somewhere that unplugging something will give a bit better performance?. Thanks people.
  13. L

    2 door Range Rover inner panels.

    Hi all. Just a quick one. Do the drivers footwell and it's adjoining side panel unbolt from early Range rover classics. Mine are rotten and need to be replaced. I know the later classics have spot welded inner panels but was wondering if the earlier ones are easier to remove? Thanks all.
  14. L

    Series Gearing

    Hi all. Looking for some advice on my series 3 SWB V8. It is fitted with Santana axles and I was told by the vendor that it had an Ashcroft overdrive transfer box at some point. It sits on 33 inch tyres. My problem is that I am not getting very much top speed out of each gear. It runs out of...
  15. L

    Panel sealant

    Hi all. Do any of you knowledgeable people know the name of the sealant that is used to seal between panels. It cures like toffee or chewing gum with a very similar consistency. I have been to lots of motor factors and they all keep offering me tiger seal or tech 7 as well as silicone based...
  16. L

    Rear shock options

    Hi all. I'm having a bit of a predicament with my 1977 series 3 SWB. It has been lifted by the previous owner using extended military shackles, parabolic springs and 33 inch mud tyres. It is very impressive and looks great. My problem is that the standard Pro-comp ES3000 shocks that are...
  17. L

    Wanted Isuzu conversion plate

    Hi all. I was just wondering if any of you nice people have an Isuzu 2.8 turbo diesel to series 3 gearbox conversion plate you don't want lying around. I know it is an older conversion and people have moved on to other diesels at this stage so I was hoping that somebody had one lying around...
  18. L

    TD5 leaking fuel rail.

    I'm just getting round to removing the cylinder head (15p) because of the dreaded fuel leaking into oil problem but before I go that far I was wondering if anybody could point out any other way the oil and fuel can mix other than a cracked fuel rail. I fitted new genuine pert seals and washers...
  19. L

    TD5 Cylinder head swap

    Anyone know if a 10P head is interchangeable with a 15P head? Cheers guys....
  20. L

    TD5 injector seals not sealing

    Hi all....I have recently replaced my injector seals and washers with new genuine parts after noticing that the oil level in the sump was rising slowly. When replacing the injectors with the new seals and washers fitted, I noticed that a couple of them were kind of loose fitting back into their...
Back
Top