Search results

Hi I am having an overheating issue on my P38 2.5 diesel auto which has now developed a second problem of the engine surging from tick over. When you take foot of throttle the revs drop to normal then engine starts surging uo to about 1500 rpm. I am suspecting it may be the gead gasket failing...

P38 2.5 (BMW straight 6) Have had a few overheating issues since having to replace a split hose at rear of engine. Refilled system with new coolant and water. All seems good but temp gauge sits a full mark higher on temp guage, more near center of normal. Before problem with split hose it would...

Hi, I am after your very knowledgable help if possible. I am after replacement copper washers for the diesel injectors on my rangy. My motor is a 1995 2.5 straight 6, the BMW engine. I had a faulty injector, now removed and have bought a good used set of 5 ( non wire) as spares. My problem is...

im after a part number for a hose on my 1995 P38 2.5D bmw engine. A hose split at the weeekend. its on the left hand side rear of the engine. above the starter motor but below rhe inlet manifold. Looks like it comes engine and bends around back if engine. Iy looks like it may be a heater hose

Just been reading up on start problems for diesel 2.5 rangy. Mine was faultless till xmas eve. went to shops but while out, when I went to start my rangy I noticed the glow plug light did not come on and engine was bugger to start, only just fired up after long cranking. I am reasonably ok at...

Hi. is there an easy test to check operation of fuel flap solenoid. All doors lock/unlock as normal but fel flap does not work. It is in the unlocked position at moment and button on dash does'nt appear to do anything

Hi, is there anybody on or near Anglesey who has a fault code scanner which can read and clear fauts on a 95/96 P38 2.5 diesel auto range rover. The main and only fault code problem I have showing is the "SRS" airbag fault. I can bring car to you to get scanned if anybody can assist at the right...

Hi can any body let me known where the srs ecu module is mounted on a 1996 2.5 diesel p38. Thank you

All driving fantastic then had very stiff gear change out of 5th and could not get any gears. box wad making few odd rattles but then got 2nd gear when speed had dropped. pulled into layby and stopped. I could see smoke from under bonnet so had a look. Smoke was billowing from between rear of...

Hi. I tried to select low gears on my P38 last week and nothing happened (was working fine previously) The light on the switch just flashes and low gears are not selected. I checked underneath today to see if all connections were good on plugs etc and all looked fine. I did notice however...

Hi, i have an "M" reg P38 2.5 diesel. Alls well but today I pressed the button on the dash board which selects low gears and nothing happened except the led on the switch started flashing on and off ? Any ideas what the problem is or maybe. It was working fine two weeks ago. regards

Hi, Recently bought a R/R 4.6 HSE, everything appears to work fine but I have noticed that when you select reverse the drivers side electric mirror tilits upwards on it's own accord? I did enquire and have been told you can disable this function by setting the switches in a certain...

Hi, anybody near Merseyside breaking a 110 or 90, I need a replacement steering columb for mine. I expect the shafts are the same lenght but wait to be corrected. I just had my steering checked out and a new track rod end fitted but when the steering wheel was about to be repositioned on the...

Hi, I am fitting a radio in my 110 in a couple of weeks and just wondered where the best place to install speakers would be. It has got a roof lining throughout if this makes the job easier or more practicle. Regards SC

Hi, I have a 110 and all is well but on way home from Wales on Monday I noticed that the steering became heavy when turnin left or right. In fact it felt as though there was blockages in the the steering wheel turning, you could start to turn then it became hard to move then it went a bit then...

Hi, just fitted a new fan switch on my 110, no problems so far. Before this somebody else had fitted an old fan switch of a S3. The fan on my 110 is seized and I am about to change it aswell but before I start stripping things I want to see the replacement in full working order beforehand...

Had to go out in the snow today, no trouble at all for super landy. Used all combinations of gearing to overcome all we came across. just perfection...

Just fitted a new washer nozzle to the 110, it's so good now it works. Had to employ the small helping hand of my 14 year old daughter to put the m13 nut onto the new nozzle though. No room for big hands with a spanner in that space in the bulkhead. Heater unit coming out Sunday and getting...

Just finished fitting my new fan heater switch and control cable to my 110. No diffrence, fan still not working, has to be the resistor or motor brushes that are stopping it now. Fuse is fine and power at fan wires. I did find one problem though when fitting the new cable onto the fan box...

Right, I am about to set about fixing my heater in my 1988 110 2.5D N.A. I have bought a new heater control switch as the one on mine was broke. I can see where the two cables attach from the right hand side controls but not yet looked where the fan motor control cable goes to. When i...