Search results

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
  1. T

    Locking wheel key

    Definitely has a 38 on the top.
  2. T

    Locking wheel key

    Hi, could anyone advise which locking nut socket I need and best place to get one? Cheers…
  3. T

    Injector removal help

    Only nearly had one mishap. Placed new injector into the port then went to make a brew.when I came back out I noticed something on the floor…(copper washer)…it must have fallen off the injector without me noticing Good job I saw it or I would have put everything back together not realising it...
  4. T

    Injector removal help

    Rough idle,engine shaking and bad fuel economy. Disconnected each injector in turn and the dodgy one made no difference when disconnected. Have now replaced said injector and cleaned out intake manifold and ports. All I can say is it’s now like driving a different car. First time attempting...
  5. T

    Injector removal help

    Do you reckon this was my problem?
  6. T

    Injector removal help

    Can I just drop copper washer in the port before the injector or might it get stuck?
  7. T

    Injector removal help

    Any tips on stopping the copper washer dropping off when I put new injector in?
  8. T

    Injector removal help

    The copper washer even came out with it!Happy days so far….
  9. T

    Injector removal help

    Cheers matey…
  10. T

    Injector removal help

    Cheers. Have intake manifold off, will I still be able to start it?
  11. T

    Injector removal help

    Pic
  12. T

    Injector removal help

    Thanks for the quick reply. Engine was hot when I started, this is wher I’m at. Nuts are off clamp and injector twists from side to side.will the clamp just lift out with the injector if I can get something underneath to pry it up?
  13. T

    Injector removal help

    Hi all. Have just removed the nuts from the thread on the injector clamp and noticed on the threaded posts the spline top is sheared off on one side. Do these need to be removed to get injector out or will come out with them still in place? Injector is twisting side to side but need to obviously...
  14. T

    Shaking at idle

    Could you or any other members recommend anywhere for recon injector? Been looking on line at Pfjones… anyone recommend this guy? gonna cost about £100 with my old one posted back to them. Cheers….
  15. T

    Shaking at idle

    Thanks for all the helpful replies. A little update that might help you knowledgeable people help me diagnose the problem. got home from work and once again carried out the disconnect/reconnect test. When I started the engine it seemed to be idling ok so I disconnected the suspect injector...
  16. T

    Shaking at idle

    Thanks for all the advice. Will I have to remove inlet manifold? What is a seat cutter? Will I need new copper washer and a seal? Any recommendations where to get good reconditioned injector for F1 TD4 facelift 56 plate. Cheers
  17. T

    Shaking at idle

    Any ideas anyone please? Does disconnecting one injector and not noticing any difference in how the engine runs mean that said injector is knackered? Cheers…
  18. T

    Shaking at idle

    left off number one connector and started engine(hesitated slightly but started first time). Check engine light came on and light went out when reconnected Anyone make any sense of all that? As you can probably tell, I ain’t no mechanic Cheers…. Should I start spraying plus gas around injector...
  19. T

    Shaking at idle

    Ok, just tried the disconnect each injector in turn test to see how it would idle. From left to right facing the engine from the front of car 1 2 3 4. Removed connector from number 1 made no difference to how engine run. 2 & 3 engine spluttered. Number 4 engine spluttered but a little worse than...
Back
Top