Search results

Has anyone fitted replacement outer front wing panels to a 90 and are happy with them? I see there are a number of sources, including those manufactured from ABS! Ideally I'm looking for original quality that will just bolt to the original fixing points and have the correct profiles. Too much to...

Hi All. Does anyone have a schematic (circuit diagram) for the NNN TD5 ECU? Thanks.

R380 "Stumpy" short bellhousing gearbox. This gearbox is designed as a stronger bolt-on replacement for the LT77 and has a shorter bellhousing than the 300TDI and Discovery R380s. It was purchased for a now abandoned V8 project where my plan was to replace my existing LT77 with the R380...

2x Allmakes MUC4299 Series 3 and early 90/110 vent seals, new and unopened 2x Bearmach BR0743 Rear Quarter Window seals (the ones either side of the rear door). For 5 mm glass, so Series 3 or early 90/110, new and unopened £20 the lot (collect East Dorset), £5 postage mainland UK

Evening All, I've finally started the reassembly process on my 1989 90 and am hoping to get the side panels back on shortly, using new seals. I beleive the correct part for my year is MXC2031, but I also see ALR5055 and AML710070/60 listed (presumably for later models). My question is, is it...

I recently purchased a Landrover part from a private seller on ebay. I waited a couple of weeks and nothing arrived. I then checked with the seller and he stated that it had been sent by Hermes and passed on the tracking information. This reported that there had been "some delay" and to wait a...

Whilst rebuilding my LT77, I notice that the inner hub of the 1st/2nd synchro was fitted the opposite of what the manual describes, i.e. it should be fitted with the radial groove on the inner hub facing the reverse gear but was fitted the other way up. I was intending to rebuild it as per the...

Having replaced my 19J with a 200tdi (which needed a new turbo and loads of other parts), I decided to remove the rear tub etc. to get good access to the chassis for painting and rustproofing. Whilst I can get to it, I'll just remove the transfer box to check the input shaft splines me...

Anyone changed their tub cappings recently? Looking for a 6" section of a tub capping to repair my old ones. Can be 90 or 110. I know you can buy repair sections but I am concerned that the profile isn't quite correct. Thanks in advance!

Wanted- Turbo housing for 200 tdi Discovery. It is the cast part that bolts to the manifold I am looking for that bolts to the turbo assembly. Mine has two cracks in it.

300tdi Discovery engine. Not heard running but purchased as an c.85k unit from a dependable source. Change of plans force sale. Complete with fuel injection pump and alternator. Located East Dorset. £300

Combined radiator with oil cooler for 19J engined Turbo Diesel 90 or 110. Proper metal construction, not cheap plastic. Removed from my own working truck. Collection from East Dorset £60

I am currently repairing my bulkhead on my 1989 90 and have noticed that there are two small factory made holes either end of the windscreen frame ledge. Were these intended for drainage (under the seal) and is there a concencus whether they should remain? I ask because it is in exactly these...

Whilst addressing some slight corrosion on my 1989 90s bulkhead, I thought I had better check the A-post drain holes. At first I couldn't find them- they were completely obscured by mud. A few pokes with a screwdriver found them but to my horror they both had an inch or two of mud in them. All...

Finally got around to getting my old 200TDI back together and just about to fit the flywheel housing (new Dowty seal fitted). What is the general opinion on this- gasket or sealant or gasket with sealant? I have the ERR1440G original style gasket, which has the raised ribs to help seal, but...

Like spannering and using my truck in East Dorset and wondered if there are any like minded fork out there for trips to the Plain etc?

Hi All. I am in the process of rebuilding an ex Disco 1.2 transfer box and have purchased a new one piece cross pin and diff gear set from Ashcroft's. I have built up the diff using shims supplied with the gasket set, but am a little concerned how course it feels when spun. There is no locking...

...got around to introducing myself after lurking here for over a year. Having been ferried about in a 1973 109 Safari during my childhood, the bug bit and I finally got to scratch the Landy itch last Summer. I have a 1989 90 and am now planning to replace the original 19J TD lump with a V8...