Search results

Just a quickie, I assume that I have to remove the whole seat to work on the seat base, I need to do some repairs to the leather. Can I just pull the plugs without disconnecting the battery? (Memory seats etc, etc.) Does anyone have the set element repair kits and the uprated thermostats, I need...

A long shot but I was wondering if anyone has a picture of the fresh air flaps in situ showing the servos. I am going to be taking the dash out and was going to attempt to get them working, the drivers side is seized. I have been told changing the servos is a right royal PIA and I was was trying...

Hi y'all, something has bugged me for ages so I thought I would throw it out there. Because I am an old fart and stiffer than woody in a porn film I always drop the car to access to climb in and out. One thing that bugs the life out of me is when I do it the car drops like a stone on the front...

I am probably sure nobody would want it but I have an upper tailgate that I am going to be taking to the tip as I have fitted a replacement. It has the usual rusty bit above the number plate but would be repairable and the whole unit would need repainting etc, the glass is fine. There are no...

I have been trying to find the pinout detail with the wire description for the RH white connector behind the footwell. I have done the LH connectors and found the diagram for both of them but not the RH ones. I have soldered the large connector that connects the heater fans on the RH, I am just...

I just had my rear calipers replaced a couple of weeks ago and a full brake bleed to replace the old fluid. I am noticing that each time I switch the ignition on now that the brake pump runs for a lot longer than it use to. It always use to run for a couple of seconds but now it is close to a...

Just on the off-chance I was wondering if anyone had a complete rear upper tailgate in or around the Poole area with no rust. Mine, as seems to be the norm, has rusted along the lower seam and as I have to also do other repairs to it and re-spray it I thought it would be faster to get another. I...

Does anyone know the pinout/description of the 2 connectors beside the inertia switch in the RH front kick panel (RH Drive). I did have a picture way back when of the colour codes and the connector. I have soldered the connectors in the LH kick panel a few years back and want to do the same. I...

When the head shears off the torx bolts on the rear bumper can the bumper still be removed with the threaded bit still in? I seem to remember reading a post a while back that so long as the flange has gone the bumper will still slide off and you can drill the remains from the bracket afterwards...

Well for those of you that have read my posts regarding the suspension issues I am finally throwing the towel in. I am going to replace the lot with springs, the question is are the Britpart ones any good, where is the best source and will I need anything else additional to the kit. At least I...

Well it has only taken me 2 1/2 years to get around to replacing what appeared to be a faulty LH rear door latch. (My apologies Marty) I now have the interior and puddle lights and the door open message coming on when I open the door however, I had thought that this switch being knackered also...

Very quick one chaps, until I can get the problem sorted with my ride sensors I have bought a kicker lite, can this be left plugged in continuously?

I had to swap out my EAS valve block due to a leaking exhaust valve and I thought I would try and fix the constant (and very consistent height) lean to the RH issue (2 3/4" on std height) I have tested the right rear sensor which I had thought was the issue but it has tested absolutely fine. I...

Hello all, been a while since I have been here, still breathing though! I hope you are all doing ok. I remember reading many moons ago a good step by step on recalibrating the suspension using calibration blocks (I have a set) but despite searching I cannot find the little beggar. Does anyone...

Anyone had a height sensor apart to clean? If so how do they come apart? I have a spare that I have done a resistance test on and it is ok through about 75% of rotation an then goes flat. I was hoping to see if I could clean the inner track. Visibly there doesnt seem to be a way in......

Are the newer type of sensor compatible with the older models, I have to pull my old ones to check and thought if I bought one rear and one front I could swap out if needed. Mine are handed LH and RH and want to use the “ambidextrous” ones so I can use either side.

What does the last tab on EASUnlock actually tell you (Get Sensor Heights)? The data on mine seems to be all over the place although the calibration tab is not that far apart, having said that the car still leans 2" lower on the drivers side. I haven't got around to calibrating though. If I was...

My rangey is a 97 4.6 HSE, are the eas ride sensors swappable from side to side on this one? FR - FL and RR - RL? Cheers

Has anyone come up with a solution to re-tipping the rubbers on the EAS solenoid valves, the small ones that seat on the conical orifice in the valve? mine have deep rings in them and I think they are leaking

Have been doing the bags and shocks along with numerous other bits and bobs and was hoping that when I changed the shocks that a creak/clunk noise would disappear. It is on the RH front and occurs when the suspension is rising or lowering or when jacking. As the suspension rises it seems to...