Search results

Hello, having trouble finding a uprated alternator option for my rrc... Any suggestions? I would like around 80Amps..

Small problem, have my freshly rebuilt 3.5 v8 in and am trying to get it started, got it cranking fine, oil pressure rises like it should but no spark... We installed a new electronic distributor with a new coil and leads that all came as a kit. How I wired it up was exactly the same as the old...

Here's the latest project... 1974 Series 3 SWB. Some morron has riveted sheet aluminum over the soft top hoops and made his own hardtop, so will be converting it back to soft top....started with a new fuel filter and battery, but needs a frost plug done before any more driving... Here's a...

What's the difference between the 3.5 vs 4.6 heads in general?

wish me luck, lpg setup on the end of a 3.5 fuel injection plenum chamber and intake manifold with the injectors blanked off...should be a lot more flowy that the 4cyl throttle body setup with ****ty lpg feed that is on the engine right now! I will have to tap a hole just after the throttle...

I have got myself a pair of axles, any way of telling if they are 24 spline from these numbers? Any help would be appreciated...:)

Range Rover Classic 3.5 on Lpg Put new exhaust system on, then first start the vehicle overheated, drained coolant, flushed radiator, new thermostat, new temperature sender...and it still over heated... So I decided to pull the water pump off.... But the rotors appear fine!? Now I have had...

Will be putting all my progress on here, will hopefully poke away at it over the course of a year.... 3.5v8 on dedicated LPG Plan is to remove the two lpg tanks in the original fuel tank location, install a fuel tank, and put an lpg tank in the boot so I can run it dual fuel.....I do like the...

Just seen this on Trademe here in NZ, what's some opinions on it?? https://www.trademe.co.nz/1710668352 Reason why it's so cheap?!

Just doing a bit of research, what would be involved in swapping out a lt77 for r380 gearbox? Any changes in crossmembers and will it work with the existing transfer case? It's in a 1984 range rover classic so it's the long stick version, and suffix d, so weakest of the lt77s... Thanks!

S3 with the original engine swapped out for a Nissan ED33, 4cyl engine ( out of the Civilian Bus) The gearbox has been getting worse and worse recently, and then as of 4 weeks ago it lost a tooth off first gear and reverse gear, so have been babying it around ever since but now it is completely...

Just purchased this 1983 classic... 3.5 converted to full time lpg(will be changed back to petrol in the future) 5 speed manual (being a 1983 this is a suffix D LT77 Gearbox?) It's going to need a bit of rust work done to it, main areas I can see atm being doors, sills, and roof... But I'll...

Just helping a mate out with lifting a stock Discovery 1 V8, whats the best option as far as a lift kit goes? its not mean to be a huge lift, but i'm thinking that a 2 inch suspension lift, because we don't want to put everything out of whack... or what happens with a 3 inch and taking the sway...

managed to get the old horn off a 2a, but was wondering if its an original landrover part?? its got AUTO LITE pressed onto the cover and its received a cheap paint job somewhere along the line.... also was wondering, do they have an earth wire running out of them, or do they earth through the...

would series 2a headlamps fit into a series 3...? thanks

just been looking at getting a set of the RM door tops, but i cant see anywhere on the website if theyre for a series 3....o_Osorry probably a really dumb question but just making totaly sure!!! thanks....

if i fit parabolics and 235/75/r15 continental cross contact AT's would i be at any risk of damaging the panels/ mud gaurds of my series 3 because of the increased articulation......?? i want to replace the current springs as one corner is a bit lopsided so paras seem a good upgrade..., and the...

how do i go about removing the wiper switch on a series3? ive narrowed down my wiper problem to the switch but i cant work out how to get the thing off to either adjust or replace it.... - any advice? thanks!

hello, looking at geting some paint for touching up my series3 side panels, not a complete paint job, there are just some areas that seriously need some paint. does anyone on here have a chart or list of the colours used so i can take them into a local shop to get them matched up....also would...

small problem here, my passenger side - im in nz so we drive on the left, so left side, headlight is only working on normal beam(dont know the proper way to say this...) the photos below will probably explain it better that anything so if anyone know the cause of my problem id be grateful, ive...