Search results

Disco 2 rear chassis leg repair plates - pre-cut. Been sat in garage so a little bit of surface rust. Free to anyone that wants to collect, from Conwy, North Wales.

The murderer had thought that he had covered his tracks by having two accomplices take his wife's Disco that he used at the time and burning it. JLR still had the data that had been transmitted by sim card saved and this told the police where the car had been at the time of the murder and even...

Advertised our disco yesterday. We had twelve people asking to see it. The second person who came bought it for £1900. It was my wife's car and she has had it since 2007. There were a few tears in her eyes when it went. It would have gone some years before without help from members on this...

We have a buyer coming to collect the car shortly. Would you give them both parts of V5 or keep the larger piece after they have filled it in and send it off yourself?

Took the starter off and used a repair kit to change starter solenoid contacts and plunger. Fitting the starter back on I fitted the two bolts and then went to fit the nut at the back. Dropped the nut and lost it somewhere. I went to find another and realised I had been trying to fit the nur...

The replacement fuseboard came today but I must have done something to one of the connectors. There are two similar ones 587 and 588. The yellow one goes in OK but I must have done something to the grey one. There are tabs that should be flush but are stopping the connector going in. See...

The Left hand indicators on our 2003 discovery 2 td5 work fine. The right hand indicators don't work at all. Not with stalk switch, hazard switch or key fob. Tried connecting up a trailer board and exactly the same. Tried swapping the relays around in the passenger compartment fuse box and...

I have fitted a replacement TD5 to our disco. The installation is nearly finished. It is just thew wiring. I have connected up the passenger side and a couple of the glow plug connectors. The silly question is where does the main loom sit? Do I bolt on ther fuel cooler and fasten the loom...

Another problem with the loom that came with the engine I bought. Not only are the connectors for the EGR modulator missing, but there are also two multiplugs missing that connect to the engine compartment fusebox. Shown above. What are these for and are they essential?

I need to try and source a plug that connects to the air-con multi socket on a td5. The plug is female and is on the wiring loom and looks like like this - The socket on the compressor looks like this -

I have a replacement 15p TD5 engine mounted to the gearbox and chassis of my 2003 discovery TD5. Aircon but no ACE. The original wiring loom had connectors which fitted on the EGR solenoid but the wiring loom with the replacement engine doesn't. Do I ignore this or fit my original loom?

I have installed injectors in this engine I have bought and have rotated the crank till the cam on No 1 is high and the number one is by the cam locking hole. I have then tightened down the adjustment screw till it won't go any further and then backed off just over 360 degrees and tightened the...

I have genuine land rover injector washers. I notice some people anneal them. Is it necessary?

I have tested the No. 1 injector pocket for cracks on the original cylinder head that had been removed. This small crack showed. Is it big enough to have caused quite a lot of diesel to escape into the rocker shaft area? Thanks.

Has anyone here ever sent an injector off for testing? There are quite a few offering the service on Ebay with prices ranging from £7 upwards. I am just wondering how well these services work.

I am tidying up the wiring loom and there is a loose white/yellow wire. I have tried to see which pin it goes to on the ECU with a multimeter but cannot find a connection at the ECU. Also the black wire from the oil pressure switch connector at the oil cooler has broken. Should there just be...

Just seen a video of this miracle spray. https://peppermintberri.com/products/multipurpose-rust I wonder if it does anything much at all. I doubt it. Lol.

We have got the engine to here but the hoist won't go higher. Trying to think of a way to support it so can remove levelling device and shorten distance to jib.

Does anyone know how much a complete TD5 engine weighs? I am trying to work out if I could carry it in the back of a small hatchback or in a small trailer like an erde 122. Thanks.

We have disconnected nearly everything needed (I hope) and just have the two long gearbox bolts and the engine mounts. Rave says to undo the bolts holding the mounts to the chassis and afterwards remove the top but holding the mounts to engine. Why can't I just remove the top but and leave the...