Search results

Hi What does this little pot do on the top of the engine? gets the dribble from the injectors on this perkins engined 2A. there is a brass thing on top and a pipe to the tank and one to the inlet manifold-thanks in anticipation of shared wisdom.

I Haven't yet investigated, BUT, when i switched on panel and interior lights in error- we got a noise like an M60 machine gun... what could it be? Quite fun really but loud and proper rat a tat... shooting up BMWs et al. Odd... (slower rate of fire compared to general)

Being of small brain long tubes bother me. the track rod we took off a 2a is 1096 long, but a spare is 1173 approx- why? i only have S3 and S2a and S1 where can i find data? the factory manual (white Book) doesn't have info. I ordered a replacement from paddock but says only use S3 TR Ends.......

Just a few images of the broken ball joint thread , something i would not have thought possible. My Very strong young Trainee told me that it must have been faulty. can you see what the cause was? hint 24 inch stilsons involved. The replacement joints were on the bench at the time...

HI the previous owner had cut a section out of front cross member to try to lube the idler which was seized. we tried jacking with steel on the shaft and a 28 pound hammer (they do exist) Nothing moved but the chassis bent. Then we decided to rebuild the relay with new parts from a new relay. so...

Hi, Has anyone strong opinions on these panels? what paint is needed for them? Are they appropriate on a series 2 restoration. I am having real problems getting a wing straight enough to fill due to my inability to shrink the Birmabright alloy......

hi is it possible to change all the main bearings with the engine in place? thanks

What is the name of the bracket which is about 100mm square that bolts to the chassis outrigger and to the rear end of the sill on a station wagon??? just trying to buy one and i cannot find them....Made of 3 plates at 90 degrees.

HRH Duke of Edinburgh designed a Land Rover hearse for his own funeral On Saturday 17th April 2021.

HI, has anyone got the bits to convert my hand brake lever in a series 3 to the short straight one found in series 2?????

CAN you change the big end and mains on a 3 bearing crank with the engine in place?

Hi, why is a land rover oil pump £300 and a pattern £40? do they work- is there a video anywhere showing how to check clearances? - I have workshop manual. What does bad look like??? thanks

hi , can anyone send me a photo of these seals and which way they are fitted to the sries 2-3 land rovers?

HI, does anybody have indepth knowledge of seat boxs? Is the 90/110 seatbox same as series? can you fit a 90/110 under seat box to a series seat box? or do i use plywood as before? Thanks

Hi, does anyone have a steering wheel with horn push? I would like the one with wire spokes. many thanks for looking at my advert.

Hallo At 4 pm a group of chaps will help put the roof back on my 2A 109 SW. How do you get the Bluddy seals in place?

hi has anyone in the midlands got any glass for the sliding side windows in a series 2-3 station wagon? Mine have got welding/cutting flash on them........ offer cash and or Cider

Hallo. after being left overnight I was curious to see diesel over the floor and on the inside of the timing belt case. it was dry yesterday- from the pooling it can only entered from behind the camshaft sprocket. Is this likely? it had not happened in the last week or so that we had cover off-...

I notice with horror that the haynes manual says use new main bearing cap bolts and big end nuts. is this really necessary?

HI I Am new to this engine and i cannot understand the books. 2 questions: if the engine has no flywheel fitted how to i time it to change the cam belt- there are marks on the cam pulley and secondly; Does this look like oil from the crank front oil seal which should be replaced? thanks.