TD5 90 Project

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Bonnet Sound Deadening and prep for Raptor....
IMG_1219.JPG

419C014B-44C1-4FCC-B671-A58A020E4338.jpg
 
UniPol Etch and Raptor 50psi at shoots gun. Pics are straught after first coat application, so glossy, will dry matt / satin. I almost forgot how stinky it its until i took my mask off lol! :rolleyes:
love working with Raptor, easy to apply and like the finish, i specifically want rough texture, soo i will be doing the truck, gun metal tintable raptor with the black checquer plate, this is just a tart up, bonnet is gonna get it soon anyway so for now it all gooda ! and decided to just buy a new bumper and raptor that, much less hassle than trying to rub down my rusty one.

IMG_1234.JPG
IMG_1236.JPG
IMG_1239.JPG
IMG_1240.JPG
IMG_1242.JPG
IMG_1242.JPG
 
Last edited:
LAST OF THE BLACK BOGEYS!!

Final Dust off and done, just got to wait a few days for full cure, got the wood burner going in the workshop to take the damp out the air etc.
IMG_1258.JPG
IMG_1269.JPG
IMG_1265.JPG
IMG_1268.JPG
 
Have a few drying room type heaters (long white cylinders) and a fan going in workshop to try help fully cure, odd sutff changes colour goes a bit blue when drying then back to black again.
POXY EPOXY does not like cold, the applicaiton was withinthe temp tolerances for the product, just means S L O W.....
 
Yep just a repaint, same as before but with raptor instead of sheite stone chip!
Only a temp thing, and chance to play with new compressor, new bumper soon and steering guard, wider arches, new shocks n springs, then the clutch......
New portable daylight, light bars are fine but the casing just corrodes, but they cheap and they bwight as fook!
 
Done, Sensor is designed to be fitted as below, to a coolant exhaust / waterhose on a marine engine) Range is -20C to 150C, popped a bit of shrink wrap along length of the sensor wire, actual sensor is metal.
IMG_1776.JPG
IMG_1781.JPG
IMG_1797.JPG
 
Another sunday, another ball joint......Replaced with Lemforder. think the old was was made by Happy Shopper....:mad::mad:
Thought i had one lying around, so after a rummage ( which looked like a dog digging a hole in sand) found it in the garage stored with door interior parts WTF ? dont ask.

WhatsApp Image 2022-09-25 at 2.06.22 PM.jpeg
 
FFS Throttle Potentiometer fix.
Did not knwo this was a TD5 common 'thing', anyway flats spots on throttle then lost throttle, MIL light on but engine running.
All points to wire chaffing somewhere, so considering i have the attention span of a kitten on cocaine, so dont play nicely with broken wire tracing,
I decided to just knock up my own jump loom, after mucheos researcheos seems the thing to do. not keen on chomping the ecu wires, so decided to make it a full clean install and orginal wiring left intact just disconnected, so reversable if one day i decide to trace the brake.
So crimped on ecu females to the jump wire and switched them out ont he Black ECU plug.
Cue A team music, roll ups, john smiths, and my best 'leave me alone' look to the dogs and mrs I set to it.


IMG_5107.JPG
IMG_5108.JPG
IMG_5109.JPG
IMG_5115.JPG
IMG_5113.JPG
IMG_5114.JPG


Test drive all good, much betterer no more flat spots and having to drive home on tick over.
 
Last edited:
Back
Top