- Posts
- 18,950
- Location
- Buckinghamshire, UK. ('95 DT)
In the Matrim kit? Yes, there is.
What did you do with your Range Rover today
- Thread starter Dopey
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
In the Matrim kit? Yes, there is.
RangeRoller dt
Well-Sprung Member
- Posts
- 14,258
- Location
- Trapped inside my head @ LZ asylum
If you have a full LR service history, £20G Noel Edmonds edition that needs to be original then fair enough.
0therwise Kev12’s Mulsion mop tactic works well.
0therwise Kev12’s Mulsion mop tactic works well.
biketeacherdave
Well-Known Member
- Posts
- 4,650
- Location
- south east london
Today I replaced the grotty old headliner, with new fabric from Martin trim!
[GALLERY=][/GALLERY]
Nice job there I'm about todo my l322 just looking at samples before I buy and I'm testing other spray glues which are repositionable as you say the usual stuff is instant grab no 2nd chance
- Posts
- 5,681
- Location
- North Manchester
Thanks for that. They are not too far from me and my headlining is sagging and full of mold spots. Didn't see a shagpile option on their website though.
May be even put some colour changing led's in there while i'm at it.
- Posts
- 5,681
- Location
- North Manchester
Can you let us know how you get on with the alternative glue please? My disco was a pita with the instant grab.
Tenebreaux
Well-Known Member
- Posts
- 3,826
- Location
- Armagh
New front calipers and various bolts arrived from JGS. Pretty good service and reasonable delivery charges to NI.
Tenebreaux
Well-Known Member
- Posts
- 3,826
- Location
- Armagh
I run into exactly the same crap in NI. My favourite is when they say they won't ship over here and they're using Royal Mail.I'd like 2 kits from Martrim, but typical UK company, they will not ship to France claiming that the glue cannot be shipped.
stemac33
Well-Known Member
- Posts
- 550
- Location
- Accrington, Lancs
If you make a mistake with contact adhesive use a hot air gun to gently warm the glue up and you get a second, third etc chance.
Henry_b
Think outside, no box required.
- Posts
- 15,351
- Location
- somewhere else
Sat nice and level in the local B&Q
biketeacherdave
Well-Known Member
- Posts
- 4,650
- Location
- south east london
Yes will do, here are some of my samples drying with the repositional glue iv dug out the last remains of what I had left over from doing my p38 so have lots to use on different glues
Tenebreaux
Well-Known Member
- Posts
- 3,826
- Location
- Armagh
Hmm. The low strength rating on that may be an issue.
I dont think thats strong enough, thats not going to last, its for paper
biketeacherdave
Well-Known Member
- Posts
- 4,650
- Location
- south east london
Yep but it's worth an experiment
- Posts
- 18,950
- Location
- Buckinghamshire, UK. ('95 DT)
I folded it back and did it in 2 halves (front and rear) working centre out with thick walking socks on my hands to slide out and push it into the nooks and crannies.
biketeacherdave
Well-Known Member
- Posts
- 4,650
- Location
- south east london
So 20 hours since I stuck my samples down.......they pulled straight off so as expected but worth a go.
3m 75 repositional spray glue is no good for a new headlining.
RangeRoller dt
Well-Sprung Member
- Posts
- 14,258
- Location
- Trapped inside my head @ LZ asylum
I’ve tried bout dozen types glue. They last bit but heat in sun then cooling, rinse repeat, open widow gone again.
Best I found was actually wilko stuff only lasted few months though.
Matrim one only one I’ve seen people do it once and for all. Gotta get all that orange right off.
Other 2 methods I’ve seen work are lining off and just board tarted up or Data’s pin method looks nice
Best I found was actually wilko stuff
only lasted few months though. Matrim one only one I’ve seen people do it once and for all. Gotta get all that orange right off.
Other 2 methods I’ve seen work are lining off and just board tarted up or Data’s pin method looks nice
Datatek
Well-Known Member
- Posts
- 43,910
- Location
- Near Poitiers SW France
Re-fitted the lower hatch top edge plastic trim and the hinged flap flap at the bottom after repairing all the broken fixing points.
Like this type
Amazon product
Amazon product
